Home  Club Car  Cushman E-Z-Go  Harley  Hyundai  Legend  Melex  Yamaha

1007
BEZEL & TAIL LIGHT, CC, YAM
tmp83CA-1.jpg
Includes: Red tail light <1). bezel (1).
Used On: Club Car gas and electric, 81-UP; Yamaha 4-cycle gas and electric, 95-UP (G14, G16. G19, G20. G21,G22).

1010125
BOLT, SHOULDER, SHORT, CC 80-92
3/8-16 x 2" bolt fastens lower end of "A" plate to the front spindle.
Used On: Club Car gas and electric 80-92.

1010126BOLT, SHOULDER, LONG. CC 80-92
3/8-16 x 4* bolt fastens upper end of "A" plate to the shock mount weldment.
Used On: Club Car gas and electric 80-92.

1010150
BEARING. THRUST, CC 93-UP
tmp83CA-2.jpg
Thrust washer bearing surface. Measures approximately .75" (19mm) I.D. x 1.37" (34.9mm) O.D. x.12" 13.1mm) W.
Used On: Club Car 93UR 8068

1010215
RESISTOR COIL. 1ST, CC 76-87
tmp83CA-3.jpg
9-gauge wire, nine coils.
Used On; Club Car electric, 76-87,
83258978

1010216
RESISTOR COIL, 2ND, CC 76-87
7-gauge wire, five coils.
Used On: Club Car electric. 76-87.
83268979
tmp83CA-4.jpg

1010217
RESISTOR COIL. 3RD, CC 76-87
7-gauge wire, four coils.
Used On: Club Car electric, 76-87.
83278980
tmp83CA-5.jpg

1010219
TIE ROD, CC 93-UP
Tie rod only. Measures approximately 19-13/16' long.
Used On: Club Car gas and electric, 93-UP.

1010347SPINDLE, PASSENGER, CC 81-UP
tmp83CA-6.jpg
Spindle assembly with bronze bushing. Used On: Club Car gas and electric, 81-UP. 10103441011392

1010348
SPINDLE, DRIVER, CC 81-UP
Spindle assembly with bronze bushing. Used On: Club Car gas and electric, 81-UP. 10103421011391
tmp83CA-7.jpg

1010413
BAG STRAP. CC 79 UP
tmp83CA-8.jpg
Black nylon weave strap. Measures approx* imaielyrWx74"L
Used On: Club Car gas and electric 79-UP (DS>.
8463

F & R HANDLE. CC 74-84
Injection molded T style handle.
Used On: Club Car gas and electric, 74-84.

1010684    SIDE PANEL PAD, CC 81-86
Extruded vinyl pad with matching surface grooves. Measures approximately 2-3/8" W x 41-1/2" L.
Used On: Club Car gas and electric, 81-86.

1010804HILL BRAKE ROD ONLY, CC 81-98
"L-Rod" for hill brake. Measures approximately 8-1/2" long with 1/4-28 threads on straight end. Uses P/N 1010932 ball joint (NOT included) and P/N 1010877 push nut (NOT included).
Used On: Club Car gas and electric, 81-98.

1010805HILL BRAKE PEDAL ROD SLEEVE. CC
tmp83CA-9.jpg
Nylon sleeve. Measures approximately .26" (6.7mm) I.D. x .49' (12.5mm) O.D. x .18" (4.6mm) W.
Used On: Club Car gas and electric, 81-98.

1010808BRAKE EQUALIZER ROD, CC 81-97
"J-hook" type rod. Measures approximately 8-1/2" L and has 5/16-18 threads.
Used On: Club Car gas and electric, 81-87.

1010877NUT, PUSH, HILL BRAKE, CC 81-UP
tmp83CA-10.jpg
Metal push nut for rod and pawl assembly. Used On: Club Car gas and electric, 81-UP.

1010878
BRAKE STOP SCREW, CC 81 -UP
tmp83CA-11.jpg
Has 1/4-20 x 1-1/8' threaded stud with a rubber bumper pad that measures approximately 1" D x 1/2" thick.
Used On: Club Car gas and electric. 81-UP.

1010880BUSHING, ACCEL. PIVOT ROD, CC
tmp83CA-12.jpg
Bronze flange-type bushing. Measures approximately .50" (12.7mm) I.D. x .62* (15.9mm) O.D. x .50" (12.7mm) L Flange measures approximately .87" (22.1mm) O.D. x .12" (3.2mm) W.
Used On: Club Car electric. 80-81.

1010889DIMMER SWITCH, CC 86-UP
tmp83CA-13.jpg
•"? Plunger-type dimmer switch with three
spade-type connectors.
Used On: Club Car gas and electric, 86-UP.
i

1010895SPEED SWITCH SLIDE, CC 80-88
Injection molded for precision assembly. (Fits S/N A8036-15260 thru A8845-160171)
Used On: Club Car electric, 80-88. 1012798

1010908-02
BATTERY HOLD DOWN, CC 00-UP
Extruded, black plastic hold down with one 5/16' hole. Measures approximately 6" long.
Used On: Club Car 00-UP.

1010908BATTERY HOLD DOWN, CC ELE
Made of molded corrosion-proof plastic, with pre-drilted anchor holes. Measures approximately 10-3/8" long.
Used On: Club Car 36-volt electric, 76-95. 70838199

1010932HILL BRAKE ROD BALL JOINT, CC
tmp83CA-14.jpg
Ball joint with 1/4-20 threads.
Used On: Club Car gas and electric, 81-UP.

1010933
SPRING, HILL BRAKE, CC 81-UP
tmp83CA-15.jpg
Pedal return spring.
Used On: Club Car gas and electric, 81-UP.

1010969ACCELERATOR PEDAL ASSY, CC81-91
Aluminum base and pivot arm with V molded vinyl pad insert.
Used On: Club Car gas and electric, 81-91.
tmp83CA-16.jpg

1010974
LEAF SPRING. REAR, CC E81-88
Rear single-leaf, painted. Uses P/N 1012180 U-bolt.
Used On: Club Car electric, 81-88.

1010988BUMPER PAD, REAR, CC 87-92
Extruded vinyl pad with matching surface grooves. Measures approximately 2-3/8" W x 35-1/B" L
Used On: Club Car gas and electric 87-92.

1011086
BUMPER END CAR CC 81-92
tmp83CA-17.jpg
Molded from high-impact plastic. Fits either side of rear bumper.
Used On: Club Car gas and electric 81-92.

1011153WHEEL HUB. FRONT, CC 74-UP
tmp83CA-18.jpg
Front wheel hub, aluminum, with 4 on 4 pattern.
Used On: Club Car gas and electric, 74-UP.
1011102 10118891011892
1011994 7114

1011284
BRUSH HOLDER, CC 84-93
Insulated brush holder with tension springs.
Used On: Club Car electric, 84-93 (2.5 HP, 10 spline motor); Columbia/Harley; E-Z-Go electric, 80-92; Legend.
tmp83CA-19.jpg

1011288FIELD COILS, 2HP, CC 84-93
$99.90 UM: EA
• ^_ Field coil assembly for 2 HP motor.
Used On: Club Car electric, 84-93.
tmp83CA-20.jpg

1011289FIELD COILS, 2.5HP, CC 84-93
. .Field coil assembly for 2.5 HP motor.
r% nTT\ r\t Used On: Club Car electric, 84-93.

1011295OIL SEAL, ELE. MOTOR SHAFT, CC
tmp83CA-21.jpg
Seal measures approximately .82" <20.8mm} I.D. x 1.38* (35.1mm) O.D. x .20" <5mm) W.
Used On: Club Car electric with GE motor, 80-84.

1011316OIL SEAL ELE. MOTOR SHAFT, CC
tmp83CA-22.jpg
Seal measures approximately .81* <20.6mm) I.D. x1.35" (34.4mm) O.D. x .27" <6.8mm) W.
Used On: Club Car electric with Hitachi motor, 80-84.

1011401BEARING SET, CC. CHD, EZ
*
Ball bearings in a plastic cage assembly (2)« steel races <2)' 3nd a tapered steel 
M •washer. Races measure approximately .88"
' * * * (22.2mm) I.D. x 1.53" (38.8mm) O.D. x .27" (6.9mm) W.
Used On: Club Car electric, 76-83; Columbia/Harley; Cushman; E-Z-Go; Taylor Dunn.
1011914

1011402BRAKEBLOCKSET.CC 81 -UP
Set of 4 blocks fastens to the brake pivot arm for smooth pedal travel.
Used On: Club Car gas and electric, 81-UP. 10108111010812

1011403
CABLE, BRAKE, CC
Flexible metal vinyl covered housing with stranded steel inner cable, and sealing boots on each end. Approximate measurements: Housing: 32-3/8"; Cable" 41-1/4".
Used On: Club Car gas and electric, 81-99. 10111251016761-01

1011407INSULATOR KIT, CC 84-93
Kit includes fiber washer (.320I.D x .885" O.D. x .130" thick); fiber washer (.465" I.D. x .885" O.D. x .130" thick); square plastic insulator (.335" I.D. x .550" O.D. x .225" thick); steel flat washer (.340" I.D x .687" O.D x .077* thick); 5/16M8 x 1/2" hex nut.
Used On: Club Car electric, 84-93 (36-volt). 1011277 1011278 1011279

1011418HILL BRAKE PEDAL KIT, CC 81-98
tmp83CA-23.jpg
Kit includes pedal weldment, pad, push nut and 2 screws.
Used On: Club Car gas and electric, 81-98.

1011420BRUSH SPRING, CC, CHD, YAM
tmp83CA-24.jpg
Brush tension spring.
Used On: Club Car electric, 80-84; Columbia/ Harley electric, 76-81; Yamaha electric, 79-91. Hitachi electric motors only.

BEZEL, TAIL UGHT, CC, YAM
tmp83CA-25.jpg
Vacuum formed ABS plastic. Makes a nice clean tail light installation. Includes black mounting rivets.
Used On: Club Car gas and electric, 81-UP; Yamaha 4-cycle gas and electric, 95-UP 1G14. G16. G19, G20, G21, G22).

1011504
HEADLIGHT, SEALED, HIGH/LOW
tmp83CA-26.jpg
Automotive replacement for #4440X. 6000 candle power high beam, 4500 candle power low beam with 3 flat terminals.
Used On: Club Car gas and electric, 81-85.

1011583                    BULBJURN SIGNAL,#194,CC 81-UP
12-volt automotive bulb, one filament. Replacement bulb for P/N's 1017062 and 20570-G2 turn signal lens.
Used On: Club Car gas and electric, 81-UP; Universal application on many golf cars and industrial vehicles.

1011603BAGWELL LJNER,CC 81-98,YAM G1
tmp83CA-27.jpg
Die cut black rubber mat with textured finish and ten punched mount holes. Con­forms to shape of bag well and protects body from golf bags.
Used On: Club Car gas and electric 81-98; Yamaha 2-cycle gas and electric 79-89

1011694BEARING, ACCELERATOR, CC 81-UP
tmp83CA-28.jpg
Brass alloy bushing pressed into a steel sleeve and then pressed into an aluminum mounting bracket. Bushing measures approximately .50" (12.7mm) I.D. Mount plate bracket has four drilled mount holes.
Used On: Club Car gas and electric, 81-UP. 2 required per car.

1011860RECEPTACLE REINFORCEMENT, CC
Injection molded black plastic ring with four pre-drilled mount holes.
Used On: Club Car electric, 84 and earlier.

1011877-02HILL BRAKE ROD, CC 99-UP
tmp83CA-29.jpg
Kit includes rod and pawl assembly, ratchet assembly with screw and nuts, ball joint, plastic sleeve, cotter pin and push nut.
Used On: Club Car gas and electric, 99-UP.

1011877HILL BRAKE LATCH KIT, CC 81-98
tmp83CA-30.jpg
Kit includes latch, 2 screws and nuts. Used On: Club Car gas and electric, 81-98. 10114041011876

1011887
DUST COVER. CC 82-UP
tmp83CA-31.jpg
Steel cover snaps into wheel hub to keep dirt and grime away from wheel bearings.
Used On: Club Car gas and electric, 82-UP.

1011977BUMPER PAD, FRONT, CC 84 92
tmp83CA-32.jpg
Formed from durable high-density blade polyethylene. Bolts on in minutes.
Used On: Club Car gas and electric 84-92. 1011094 1011880 1017080

1011997F & R SWITCH, CC E83 1/2-UP
tmp83CA-33.jpg
Complete switch for 36-volt resistor cars. Does NOT include selector handle.
Used On: Club Car electric, 83 1/2-UR 1017530-03

1012085FUSE, 36V-80A, CC 85-UP
80-amp fuse with screws.
Used On: Club Car 36-volt electric, 85-UP. O

1012142
FUSE HOLDER, 36V, CC 85-UP
tmp83CA-34.jpg
Phenolic fuse holder for 36-volt, 80-amp fuse.
Used On: Club Car 36-volt electric, 85-UP.

1012143
FUSE LENS, 36V, CC 85-UP
Clear fuse lens for 36-volt, 80-amp charging system.
Used On: Club Car 36-volt electric, 85-UP.

1012164INNER FRAME SNUBBER, CC 84-UP
tmp83CA-35.jpg
Inner frame rubber snubber. Used On: Club Car gas, 84-UP.

1012180BOLT. REAR SPRING, CC 81-UP
tmp83CA-36.jpg
U-bolt for fastening rear spring to frame. Has 7/16-14 threads.
Used On: Club Car gas and electric, 81-UP. 1014553

1012191ARMATURE, 2.5HP, CC 84-93
tmp83CA-37.jpg
Armature assembly with splined driven end.
Used On: Club Car electric. 84-93, 2.5 HP. 10-spline motor.

1012287
CLUTCH, DRIVE, CC 84-87
tmp83CA-38.jpg
Salsbury-style clutch. No longer available from Club Car.
Used On: Club Car gas. 84-87 {S/N AG8414-53441 thru AG880M35720).

1012288
CLUTCH, DRIVEN, CC 84-87
tmp83CA-39.jpg
Salsbury-style clutch.
Used On: Club Car gas, 84-87 (S/N AG8414-53441 thru AG8801-135720); Hyundai gas, 91-96 (HGG-1).

tmp83CA-40.jpg
1012289
BELT, DRIVE, CC 84-87 (10)
Reinforced belt. Measures approxtmateiy 7/8" Wx 37-1/2"O.D.
Used On: Club Car gas, 84-87.

1012303BUSHING, LEAF SPRING, STEEL, CC
Steel plated bushing. Measures approximately -36" (9.1mm) I.O. x .50" (12.7mm) O.D. x 2.12" 153.8mm) L
Used On: Club Car gas and electric, 76-UP. 10101607051

1012324
LEAF SPRING, REAR, CC G84-UP
Rear single-leaf spring, painted. Measures approximately 28-1/8" between centers of bushing mount holes. Uses P/N 1012180 U-bolt.
Used On: Club Car gas, 84-UP.

tmp83CA-41.jpg
1012338
BELT, GENERATOR, CC 84-87 (10)
Reinforced belt. Measures approximately 3/8" W x 36-3/4" O.D.
Used On: Club Car gas, 84-87 and '94.

1012415KEY SWITCH, CC G84-95
Switch includes P/N 1012505 keys (2). Used On: Club Car gas, 84-95.
tmp83CA-42.jpg

1012466 GASKET, STEERING TUBE, CC, CHD, EZ
tmp83CA-43.jpg
Die-cut foam gasket. Measures approximately 3/4" I.D. x 1-3/8" O.D. x 7/16' W.
Used On: Club Car gas and electric, 76-94; Columbia/Harley; Cushman; Davis; E-Z-Go gas and electric, 65-70; Jacobsen; Legend; Noland; Otis; Toro.
17277834

1012496
DELTA SHOCK SUPPORT, CC 81-91
Welded steel assembly bolts to frame. Used On: Club Car gas and electric, 81-91.

1012499SEAL, STEERING COLUMN CC 92-UP
tmp83CA-44.jpg
Foam pad measures approximately 3-1/8" x 5-1/8" x 1/4" thick with a 1-7/16" diameter hole in the center.
Used On: Club Car gas and electric, 92-UP. 1011018

1012505KEY,CC84UP
tmp83CA-45.jpg
Replacement key for P/N 15727. 15728, 1012531 and 1012415 switches. Not "L" shaped (large head key).
Used On: Club Car gas and electric, 83 1/2-UP.

1012507GASKET, CARBURETOR, CC 84-91
tmp83CA-46.jpg
Die-cut gasket. Measures approximately 1-9/16" between mount hole centers.
Used On: Club Car gas, 84-91 (341cc).

1012509
GASKET, CARBURETOR. CC 84-91
tmp83CA-47.jpg
Die-cut gasket. Measures approximately 1-25/32" between mount hole centers.
Used On: Club Car gas. 84-91 (341 cc).

1012511
GASKET, HEAD, CC 84-91
Composition material gasket pressed between aluminum jackets.
Used On: Club Car gas, 84-91 {341cc).

1012513
VALVE, INTAKE, CC 84-91
Used On: Club Car gas, 84-91.

1012514
VALVE, EXHAUST, CC 84-91
Used On: Club Car gas, 84-91.

tmp83CA-48.jpg
1012515
PISTON ASSEMBLY, STD, CC 84-91
Aluminum alloy. Includos rings, piston pin and retainers.
Used On: Club Car gas. 8491 (341cc).
Tips: Before installing rings on piston, always check to insure that you have the proper end-gap clearance when rings are inserted in cylinder. Consult the manufacturer's maintenance manual for proper specifications and complete installation instructions.

tmp83CA-49.jpg
1012516
RING SET. STD, CC 84-91
Three ring set.
Used On: Club Car gas, 84-91 (341cc).
Tips: Before installing rings on piston, always check to insure that you have the proper end-gap clearance when rings are inserted in cylinder. Consult the manufacturer's maintenance manual for proper specifications and complete installation instructions.

1012517CONNECTING ROD, CC 84-91
Cast aluminum rod. J Used On: Club Car gas, 84-91.

1012518
GASKET, CYLINDER BASE, CC 84-91
Die-cut gasket, 6-hole.
Used On: Club Car gas, 84-91 (341cc).

GASKET, CRANKCASE, CC 84-91
Die-cut gasket, 13-hole.
Used On: Club Car gas, 84-91 (341 cc).

1012520
COIL, IGNITION, CC 84-89
DISCONTINUEDtmp83CA-50.jpg
DISCONTINUED-Ignition coil with three lead wireslbrown, red, white) and triangle plug connector (two female and one male bullet-type), and one black lead with insulated female bullet-type connector.
Used On: Club Car gas, 84-89.

1012521COIL EXCITING, CC 84-91
tmp83CA-51.jpg
Ignitor coil with three lead wires (black, red, white) and triangle plug connector (two male and one female bullet-type).
Used On: Club Car gas, 84-91.

1012524OIL SEAL, CRANKCASE, CC 84-91
tmp83CA-52.jpg
Seal measures approximately 1.96' (50mm) O.D. x 1.18" (30mm) I.D. x .31' (8mm) W.
Used On: Club Car gas, 84-91.

1012531KEY SWITCH, CC E83 1/2-95
tmp83CA-53.jpg
Switch includes P/N 1012505 keys (2). Used On: Club Car electric. 83 1/2-95.

1012605 RETAINING RING. CC 84-UP
tmp83CA-54.jpg
For the bottom of the steering column on cars with rack and pinion.
Used On: Club Car gas and electric, 84-UR

1012665OIL SEAL. INPUT SHAFT, CC
measures approximately .73" <18.5mm) I.D. x 1.34' (34.1mm) O.D. x .24" (6.2mm| W.
Used On: Club Car 36-volt electric, 84-85.

1012683OIL SEAL, AXLE, CC 84-85
Rear axle seal. Measures approximately 1.37n (35mm) I.D. x .2.04" (52mm) O.D. x 3V (8mm) W.
Used On: Club Car gas and electric, 84-85.

1012714
OIL SEAL, TRANSMISSION, CC
Seal measures approximately .93" (23.6mm) I.D. x 1.58" (40.1mm) O.D. x .31" (7.8mm) W.
Used On: Club Car gas. 84-UP.
tmp83CA-55.jpg

GASKET, TRANS CASE, CC 84-91
Die-cut, 11-hole gasket. Used On: Club Car gas, 84-91.

1012761BEARING, 6003
tmp83CA-56.jpg
Ball bearing, open both sides. For use on governor shaft. Measures approximately .67" (17mm) I.D. x 1.38* (35mm) O.D. x .39" (9.9mm) W.
Used On: Club Car gas, 84-UP.

1012834BUSHING, DRIVEN CLUTCH, CC 84-89
tmp83CA-57.jpg
Fiber-glide type bushing for driven sheave. Measures approximately 1.53" (39mm) O.D. x 1.37" <34.9mm) I.D. x 1.50" (38.1mm) L
Used On: Club Car gas. 84-89; Hyundai gas, 91-96.

1012846GASKET, TAPPET COVER, CC 84-91
tmp83CA-58.jpg
Die-cut cork material. Measures approximately 3-3/32" L x 1-25/32" W x 3/32" thick.
Used On: Club Car gas, 84-91 (341cc).

1012868  GEAR, BALANCER, CC 84-85
Thin gear with straight teeth. Used On: Club Car gas, 84-85.

1012870CRANKSHAFT WITH GEARS, CC 84-85
tmp83CA-59.jpg
Balanced crankshaft assembly with gears (straight-cut on fan side).
Used On: Club Car gas, 84-85.

1012872
GEAR. CRANKSHAFT, CC 84-91
tmp83CA-60.jpg
Wide gear with helical teeth. Used On: Club Car gas, 84-91.

1012880
SPLASHER. OIL CC 84-91
Bolts onto end of crankshaft journal. Used On: Club Car gas. 84-91.

tmp83CA-61.jpg
1012958
PISTON ASSEMBLY, .25MM, CC 84-91
Aluminum alloy. Includos rings, piston pin and retainers.
Used On: Club Car gas, 84-91 (341 cc).
Tips: Before installing rings on piston, always check to insure that you have the proper end-gap clearance when rings are inserted in cylinder. Consult the manufacturer's maintenance manual for proper specifications and complete installation instructions.

tmp83CA-62.jpg
1012959
PISTON ASSEMBLY, .50MM, CC 84-91
Aluminum alloy, includes rings, piston pin and retainers.
Used On: Club Car gas, 84-91 (341cc).
Tips: Before installing rings on piston, always check to insure that you have the proper end-gap clearance when rings are inserted in cylinder. Consult the manufacturer's maintenance manual for proper specifications and complete installation instructions.

tmp83CA-63.jpg
1012960
RING SET, .25MM, CC 84-91
Three ring set.
Used On: Club Car gas, 84-91 (341cc).
Tips: Before installing rings on piston, always check to insure that you have the proper end-gap clearance when rings are inserted in cylinder. Consult the manufacturer's maintenance manual for proper specifications and complete installation instructions.

tmp83CA-64.jpg
1012361
RING SET, .50MM, CC 84-91
Three ring set.
Used On: Club Car gas, 84-91 (341cc).
Tips: Before installing rings on piston, always check to insure that you have the proper end-gap clearance when rings are inserted in cylinder. Consult the manufacturer's maintenance manual for proper specifications and complete installation instructions.

tmp83CA-65.jpg
CARB REPAIR KIT, CC 84-91
Kit includes: float bowl o-ringr manifold gasket, pilot jet, main jet, pilot screws and spring, idle stop screw and spring, main nozzle, needle valve gasket, float bowl retaining nut and gasket.
Used On: Club Car gas, 84-91.

1012982RAMP BUTTON, CC 84-91
tmp83CA-66.jpg
Plastic ramp buttons only. Use with P/N 1012833 movable face. (Button has tapered surfaces on recessed hole side.)
Used On: Club Car gas, 84-91.

1012987F & R HANDLE, CC 85-UP
tmp83CA-67.jpg
Injection molded handle.
Used On: Club Car gas and electric, 85-UP.

1013010FIELD COIL, GEN, CC, CHD, EZ
tmp83CA-68.jpg
Field coil assembly for Hitachi-style starter-generators.
Used On: Club Car gas, 84-96; Columbia/ Harley 2-cycle gas, 69-95; E-Z-Go 2-cycle gas, 80-94.

1013011BRUSH HOLDER, GEN., CC 84-96
tmp83CA-69.jpg
Includes brushes, springs and wires. For Hitachi starter-generators only.
Used On: Club Car gas, 84-96; Columbia/Harley gas, 67-97; E-Z-Go gas, 80-93; Hyundai gas, 91-UP; Yamaha gas, 78-95 (G1, G2, G8, G9, Gil, G14).

1013035BELLOWS, STEERING, CC
tmp83CA-70.jpg
Rubber boot keeps dirt, dust and grass out of your steering rack.
Used On: Club Car gas and electric, 84-96 both sides and 97-UP passenger side.

1013041RACK END, CC 84-96
tmp83CA-71.jpg
Inner steering rack joint.
Used On: Club Car gas and electric, 84-96.

1013046STEERING RACK GUIOE, CC 84-96
tmp83CA-72.jpg
Plastic guide measures approximately 1.17- (29.8mm) 0.0. x .75* |19mm) H.
Used On: Club Car gas and electric, 84-96.

1013052OIL SEAL, STEERING PINION, CC
tmp83CA-73.jpg
Seal measures approximately .52" (13.3mm) x 1.39" (35.3mm) O.D. x .22" (5.5mm) W.
Used On; Club Car gas and electric, 84-UP.

1013085
CABLE, F & R, CC 84-97
Flexible metal vinyl covered housing with stranded stainless-steel inner cable. Measures approximately 63" long.
Used On: Club Car gas, 84-97. 10123261018510-02

1013135OIL SEAL, FRONT WHEEL CC 82-UP
tmp83CA-74.jpg
Seal measures approximately 1.94" (49.4mm) O.D x 1.07* (27.1mm) I.D. x .34" (8.6mm) W. Use with P/N 1011153 hub.
Used On: Club Car gas and electric, 82-UP. 1011888

CABLE, THROTTLE, CC 84-91
Flexible metal vinyl covered housing with stranded stainless-steel inner cable. 90-degree threaded metal sleeves at each end with three hex adjusting nuts. Approximate measurements: Housing: 10-1/4'; Cable: 16-3/4".
Used On: Club Car gas, 84-91. 10124431013163

1013421
NUT, SPEED DOUBLE, CC 81-94
Double nut plate for beverage holder. Stamped from mild zinc plated steel.
Used On: Club Car gas and electric, 81-94.

tmp83CA-75.jpg
CUP HOLDER, SINGLE, CC 81-94
Injection molded, one-piece unit with hardware. Uses PIN 15042 replacement screw.
Used On: Club Car gas and electric, 81-94. 1011112 1011113 1013420

tmp83CA-76.jpg
1013474-25
REBUILD KIT, .25MM, CC 84-85
Includes .25mm piston, rings, piston pin with retainers, valves, bearings, connecting rod, crankshaft assembly and gasket set.
Used On: Club Car gas, 84-85.

tmp83CA-77.jpg
1013474-50REBUILD KIT, 50MM, CC 84-85
Includes .50mm piston, rings, piston pin with retainers, valves, bearings, connecting rod, crankshaft assembly and gasket set.
Used On: Club Car gas, 84-85.

tmp83CA-78.jpg
1013474B-25
REBUILD KIT, .25MM, CC 86-91
Includes .25mm piston, rings, piston pin with retainers, valves, bearings, connecting rod, crankshaft assembly and gasket set.
Used On: Club Car gas, 86-91.

tmp83CA-79.jpg
1013474B-50
REBUILD KIT, .50MM, CC 86-91
Includes .50mm piston, rings, piston pin with retainers, valves, bearings, connecting rod, crankshaft assembly and gasket set.
Used On; Club Car gas, 86-91.

1013531
SPRING, BRAKE RETURN, CC
Fifteen-coil tension spring. Measures approximately 2-1/2" long.
Used On: Club Car gas and electric, 99-UP; Club Car electric, 88-98.

1013587
F&R BELL CRANK WLDMNT, CC 84-UP
tmp83CA-80.jpg
Bell crank assembly with two machined flat-sides, approximately .242" wide, on each end. Overall length of shaft is approximately 4-11/32' long
Used On: Club Car gas 84-UP (DS).

1013649DC RECEPTACLE BEZEL, CC 85-UP
tmp83CA-81.jpg
Molded of black ABS with a fine hair-cell finish. Has rectangle receptacle hole and measures approximately 3-1/4" D. Used with P/N 66036-72 2-prong, DC receptacle.
Used On: Club Car electric, 85-UP (36-volt).

1013661MUFFLER, CC 84-91
T Replacement muffler, compatible with
original configuration.
Used On: Club Car gas, 84-91.
1012315

1013683BATTERY HOLD DOWN ROD, CC ELE
"J-hook" type steel rod, approximately
_,____________- 11.625" long. (36 and 48-volt models).
Uses P/N 15428 nut.
Used On: Club Car electric, 81-99. 10102207084

1013762FUEL PUMP REPAIR KIT, CC 84-87
^^K^X Includes body gaskets (3), neoprene and plastic diaphragm (1), and valve assembly (1).
Used On: Club Car gas, 8487.
tmp83CA-82.jpg

1013775OILSEALJNPUTSHAFT.ee
tmp83CA-83.jpg
Seal measures approximately .71" (18.2mm) x 1.38" (35.1mm) O.D. x .32" (8.1mm) W.
Used On: Club Car 36 and 48-volt electric, 86-UR

1013785AXLE, REAR, PASSENGER, CC 86-96
Passenger side, approximately 22* long £ from flange hub to end of axle.
Used On: Club Car gas and electric, 86-96.

1013786AXLE, REAR, DRIVER, CC 86-96
tmp83CA-84.jpg
Driver side, approximately 15-1/2" long from flange to axle end.
Used On: Club Car gas and electric, 86-96.

1013787
BOLT, LUG, CC
tmp83CA-85.jpg
1/2-20 x 1-5/16' long, with serrated shoulder. Uses P/N 43152-66 lug nut.
Used On: Club Car.

1013789
GASKET, REAR AXLE TUBE, CC 87-97
Die-cut gasket. Measures approximately 2-11/16" I.D.x 4-11/32-O.D.
Used On: Club Car gas and electric, 87-97.

1013794OIL SEAL, AXLE, CC 86-UP
V Rear axle seal. Measures approximately |to 1.33" (34mm) I.D. x .1.77" (45mm) O.D. x If .236" (6mm) W.
Used On: Club Car gas and electric, 86-UP.

1013860CONTACT. V-GLIDE WIPER, CC 88-UP
Copper wiper brush for V-Glide switch.
Used On: Club Car electric with V-Glide. 88-UP.

1013861STEERING JOINT. CC 84-UP
tmp83CA-86.jpg
Steering universal joint assembly.
Used On: Club Car gas and electric. 84-UP.

1013867
LEAF SPRING, FRONT, & E, CC 81-UP
Front single-leaf spring, painted.
Used On: Club Car gas and electric, 81-UP.
1010136 1015108
1012030 1015828
1012322

1013869PEDAL PAD, BRAKE, CC 81-UP
tmp83CA-87.jpg
Injection molded of black heavy-duty vinyl pad with the word 'STOP" imbedded in surface.
Used On: Club Car gas and electric, 81-UP. 1010833

1013870
PEDAL PAD. HILL BRAKE, CC 81-UP
Injection molded black vinyl pad with the word "PARK" imbedded in surface. Measures approximately 1-5/8" x 2-1/4".
Used On: Club Car gas and electric, 81-UP 10108327166

1013871PEDAL PAD, ACCELERATOR, CC 81-UP
Injection molded of black heavy-duty vinyl with non-skid surface.
Used On: Club Car gas and electric, 81-UP. 1010879

1013882BATTERY HOLD DOWN ROD, CC 84-98
Combination one-piece hold down and dual threaded rod assembly. Zinc-plated steel. Uses P/N 15615 nut.
Used On: Club Car gas, 84-98 1012343

1013887
WIPER ARM CARRIER, SPEED SWITCH
tmp83CA-88.jpg
Injection molded housing with shaft hold the wiper brush.
Used On: Club Car electric with V-Glide, 88-UP.

GASKET, PUMP COVER, CC 84-91
Die-cut gasket for impulse pump. Measures approximately 1-25/32" between mount hole centers.
Used On: Club Car gas, 84-91.

1013983SIDE PANEL PAD, CC 87-97
Extruded vinyl pad with ribbed surface and tapered ends. Measures approximately 2-5/8'Wx 41-1/2" L
Used On: Club Car gas and electric, 87-97.

1013989CRANKSHAFT WITH GEARS, CC 86-91
tmp83CA-89.jpg
Balanced crankshaft assembly with gears {helical-cut on fan side).
Used On: Club Car gas, 86-91.

1013990
GEAR, BALANCER, CC 86-91
Thin gear with helical teeth. Used On: Club Car gas, 86-91.

tmp83CA-90.jpg
1014081
BELT, DRIVE, CC 88-91 {10}
Reinforced belt. Measures approximately r W x 37-3/4" O.D.
Used On: Club Car gas, 88-91 (Not for OHV engine}.
1017188

1014089F & NEUTRAL CAM KIT, CC G86-UP
tmp83CA-91.jpg
Injection molded cam with washer. Used On: Club Car gas, 86-UP.
O

1014125  STEERING WEDGE, CC 87-UP
tmp83CA-92.jpg
Tapered plastic bushing for use on steering column. Measures approximately .73" (18.5mm) I.D. x .95" (24.7mm) tapering to .TT (19 6mm) O.D. x .43 {10.9mm) W.
Used On: Club Car gas and electric. 87-UP.

1014126STEERING BEARING SEAT, CC 87-UP
tmp83CA-93.jpg
Plastic bearing seat. Measures approximately 1.24" (31.5mm) I.O. The 0.0. of the shoulder is approximately 1.39* (35.4mm) and the remaining body is 1.31* (33.8mm). Length is 1.74" (44.1mm).
Used On: Club Car gas and electric, 87-UP.

1014173KEY, CC 76-83 1/2
tmp83CA-94.jpg
Replacement key for P/N 8204 ignition switch.
Used On: Club Car electric, 76-83 1/2. 8205

1014176
BEZEL, DRIVER, CC 81-92
Injection molded plastic fits in original factory cut outs. Driver side only.
Used On: Club Car gas and electric, 81-92.
tmp83CA-95.jpg

1014177
BEZEL, PASS, CC 81-92
Injection molded plastic fits in original factory cut outs. Passenger side only.
Used On: Club Car gas and electric, 81-92.
tmp83CA-96.jpg

1014180BULB,HEADLIGHT, CC 86-92
^BP
12-volt automotive bulb, two filaments. Used On: Club Car gas and electric, 86-92.

1014207BUSHING, AXLE, CC E85-UR G86-UP
tmp83CA-97.jpg
For use with the Kawasaki "K" model transaxle. Approximate measurements: 0.980" I.D. x 1.340- O.D. x 0.710" W.
Used On: Club Car gas 86-UP (DS) and electric 85-UP (DS).

1014211OIL SEAL, STEERING CC 87-UP
Seal measures approximately .69" 07.7mm) I.D. x 1.25" (31.9mm) x .17" (4.4mm) W.
Used On: Club Car gas and electric, 87-UP.

1014212STEERING SHAFT SPACER, CC
Plastic spacer. Measures approximately .66" (16.9mm) 1.0. x .75" (19.1mm) O.D. x _.50" (12.8mm) I.
Used Ore Club Car gas and electric, 87 only.

1014213BEARING, STEERING, CC 87-UP
tmp83CA-98.jpg
Caged roller bearing. Measures approximately .75" (19mm) I.D. x 1.17" (43.4mm) O.D. x .28" (7.1mm) W.
Used On: Club Car gas and electric, 87-UP.

1014214RETAINING RING, CC 87-UP
tmp83CA-99.jpg
Internal tooth lock washer for the top of the steering column.
Used On: Club Car gas and electric, 87-UP.

1014216STEERING COLUMN REBUILD KIT. CC
99 9 Includes bearing seats (2), column spring O O • (1), retaining ring (1), bearings (2|, steering OO wedges (2). tube gasket (1), and retaining
snap ring (1).
Used On: Club Car gas and electric, 87-93.

1014217SPRING, STEERING COLUMN, CC 87-UP
tmp83CA-100.jpg
5-coif, compression-type spring. Measures approximately 1-1/4" long.
Used On: Club Car gas and electric, 87-UP

1014235                   SHOCK, FRONT G&E.CC81-UP
Bushing mount both ends. Compresses to 9-5/8"; extends to 11-3/8", measured end to end.
Used On: Club Car gas and electric, 81-UP. 1012284 1014233 1015813

1014236SHOCK, REAR, CC E81-UP
Threaded 3/8-24 shaft both ends. Compresses to 11-1/2"; extends to 14-1/2" measured from ends of shafts.
Used On: Club Car electric, 81-UP. 10121831013164

tmp83CA-101.jpg
1014290
BELT, GENERATOR, CC 88-91 & 94
Reinforced belt. Measures approximately 3/8r W x 32-3/4" O.D.
Used On: Club Car gas, 88-91 and 94.

1014392BAGWELL MAT, CC 81-98
tmp83CA-102.jpg
Die cut black rubber mat with textured finish and four pundied holes. Measures approximately 8-3/4" x 8-3/4" x 3/32" thick.
Used On: Club Car gas and electric 81-98. 1011641

1014449CLUTCH, DRIVE, CC 88-91
tmp83CA-103.jpg
Salsbury-style clutch.
Used On: Club Car gas, 88-91.

1014453RAMP BUTTON KIT, DRIVE, CC
^*M      Kit includes plastic slides, clips and
)fmhardware.
} f         |        Used On: Club Car gas, 84-91.
© O        O

1014454RAMP BUTTON KIT, DRIVEN, CC
^      ^      Kit includes plastic ramp buttons (3) and
wj>     ^     socket head cap screws (3). Use with P/N
T T         T       1014072 movable face. {Button has
'          '       "rounded" surface on recessed hole side.)
Used On: Club Car gas, 94-91.

1014496PULLER, DRIVE CLUTCH, CC 92-UP
For removing OEM drive clutch from crankshaft.
Used On: Club Car gas, 92-UP.

1014516FUSE ASSEMBLY, CC
tmp83CA-104.jpg
Assembly for 36-volt systems. Includes P/N 1012085 fuse (1), P/N 1012142 base (1> and P/N 1012143 clear lens (1).
Used On: Club Car 36-volt electric, 85-UP.

1014523
FUEL PUMP, CC 87-UP
Mikuni pump, aluminum housing. Used On: Club Car gas, 87-UP.

1014524FUEL PUMP REPAIR KIT, CC 88-UP
tmp83CA-105.jpg
tmp83CA-106.jpg
Kit includes gaskets and diaphragm. Used On: Club Car gas, 88-UP.

1014675
LEAF SPRING, REAR, HD, CC 81-UP
Heavy-duty rear leaf spring, painted. Measures approximately 28-1/8" between centers of bushing mount holes. Uses P/N 1012180 U-bolt.
Used On: Club Car gas and electric, 81-UP. 1011149

1014728RESISTOR MOUNTING BOARD, CC
tmp83CA-107.jpg
Insulator board with two 1/4" pre-drilled holes and six 1/4" "square" holes. Measures approximately 2" W x 11-3/8" L x 3/16' thick.
Used On: Club Car electric.

COWL. FRONT, WHITE, CC 81-92
tmp83CA-108.jpg
Thermal vacuum formed from industrial grade ABS. CNC precision routered edges, smooth contours and shiny finish to match OEM appearance. Color: White.
Used On: Club Car gas and electric, 81-92. 101512302

1015225
CABLE, ACCELERATOR. CC 92-96
Flexible metal vinyl covered housing with stranded steel inner cable. Approximate measurements: Housing: 30", including threaded adjustment sleeves; Cable: 33-7/8p.
Used On: Club Car gas, 92-96 (OHV engine).

1015226*01CABLE, GOVERNOR, CC 92-96
Flexible metal vinyl covered housing and an additional braided nylon outer sheath, with stranded stainless-steel inner cable. Measures approximately 13-3/8" long.
Used On: Club Car gas, 92-96 (OHV engine).
1015226

tmp83CA-109.jpg
1015241
BELT, GENERATOR, CC 92-93, 95-96
Reinforced belt. Measures approximately 3/8" W x 32-3/4" O.D.
Used On: Club Car gas, 92-93 and 95-96.

1015247
EXHAUST HEADER PIPE, CC 92-93
Exhaust pipe used with P/N 1016821 muffler.
Used On: Club Car gas, 92-93.

1015330GASKET, EXHAUST, CC 92-UP
o
Die-cut gasket made of heat resistant, metal reinforced composition material. Measures approximately 1-27/32" between mount hole centers.
Used On: Club Car gas FE290, 92-UP.

1015371
COMPONENT BOX, CC 92-UP
tmp83CA-110.jpg
Injection molded black plastic electric com­ponents box.
Used On: Club Car gas 92-UP (OS).

1015372
COMPONENT BOX COVER, CC 92-UP
tmp83CA-111.jpg
Injection molded elecirical components box cover.
Used On: Club Car gas 92-UP (DS).

1015426FILTER, AIR, CC 92-UP
tmp83CA-112.jpg
Panel-type filter. Measures approximately 7-5/8" L x 6" Wx 1-11/64" H.
Used On: Club Car gas, 92-UP IOHV engine).

1015583BUSHING, LEAF SPRING, CC
tmp83CA-113.jpg
Urethane flange-type bushing for A-plate and leaf spring. Measures approximately .48* (12.1mm) I.D x .87" <22mm) O.D. x 1.12* (28.4mm) L . Flange measures approximately 1.12" (28.4mm) O.D. x .25' (6.3mm) thick.
Used On: Club Car gas and electric, 92-UP. 7050

1015741
FUSE BLOCK, CC G92-UP
tmp83CA-114.jpg
Injection molded 4-slot fuse block only, for use with ATC style flat fuses.
Used On: Club Car gas 92-UP (DS).

1015777VOLTAGE REGULATOR, CC 92-UP
tmp83CA-115.jpg
Solid-state voltage regulator, four-wire r connection.
Used On: Club Car gas, 92-UP.

1015923RPM LJMITER, CC 90-91
tmp83CA-116.jpg
Sealed unit with one 4-wire harness and one 2-wire harness.
Used On: Club Car gas. 90-91.

1015925COIL IGNITION, CC 90-91
V^        J
tmp83CA-117.jpg
Ignition coil with two lead wires and connector plug (one mail and one female bullet-type).
Used On: Club Car gas, 90-91.

1016110-01TUNE UP KIT, CC 84-91
tmp83CA-118.jpg
Kit includes a canister type air filter, fuel filters (2) and spark plug.
Used On: Club Car gas, 84-91 {341 cc).

1016110-03 TUNE UP KIT. CC 92-UP
tmp83CA-119.jpg
Kit includes a panel type air filter, canister oil filter, in-line fuel filters J2) and spark plug.
Used On: Club Car gas, 92-UP. .1016110-02

1016111 SPARK PLUG, BP5ES, (4,120)
NGK BP5ES.
Used On: Club Car gas FE290, 92-99; Columbia/Harley gas, 71-81; Jacobsen.

1016130F & SWITCH ROTOR, CC 83 1/2-UP
tmp83CA-120.jpg
Injection molded for F & R switch assembly.
Used On: Club Car electric, 83-1/2-UP. 10119761014829

1016166ACCELERATOR PIVOT ROD, CC 84-95
Plated for corrosion protection. Includes ratchet pawl and hardware. Rod measures y- "^* approximately .50' (12.7mm) D x 5.75" (146.0mm) L.
Used On: Club Car gas and electric, 84-95.
tmp83CA-121.jpg

1016173
HILL BRAKE ROD & PAWL KIT, CC
Kit includes *L-Rod" and pawl, ball-joint, plastic sleeve, cotter pin, and push-nut.
Used On: Club Car gas and electric, 81-98.

tmp83CA-122.jpg
1016203
BELT DRIVE, CC 92-UP (10)
Reinforced belt. Measures approximately 1"Wx 37-1/2" O.D.
Used On: Club Car gas, 92-UP.

1016342
F & R SHIFTER BASE, CC G93-UP
$6.90 UM: EA
Injection molded part that joins the shift lever and cable.
Used On: Club Car gas, 93-UP.

1016346
BUSHING. A PLATE, CC 93-UP
tmp83CA-123.jpg
Urethane flange-type bushing for A-plate. Measures approximately .54" (13.2mm) I.D. x .85" (21.5mm) O.D. x .62" <15.8mm) L . Flange measures approximately 1.09 * (27.6mm) O.D. x .14" (3.7mm) W.
Used On: Club Car gas and electric, 93-UP.

1016353DELTA A PLATE SUB ASSY, CC 93-UP
tmp83CA-124.jpg
"A" plate or "A" arm includes brass center bushings and urethane bushings on both ends.
Used On: Club Car gas and electric, 93-UR

101636001
CLUTCH, DRIVEN, CC 88-96
tmp83CA-125.jpg
Salsbury-style clutch.
Used On: Club Car gas, 88-96.
10144501016360-02

1016378-02CLUTCH, DRIVE, CC 92-96
tmp83CA-126.jpg
Salsbury-style clutch.
Used On: Club Car gas, 92-96.
1016378-03 1016378-05 101678-02

1016379BUMPER, REAR, CC 93-UP (10)
Rotational-molded, one-piece bumper. Measures approximately 5" W x 39" L Uses P/N 1016879 bolt
Used On: Ctub Car gas and electric 93-UP
(DS).

1016384
DELTA UPPER CLEVIS, CC 93-UP
Attaches front shock to spindle.
Used On: Club Car gas and electric, 93-UP.

1016385
DELTA SHOCK SUPPORT, CC 92-UP
Welded steel tower connects front shocks and "A" plates.
Used On: Club Car gas and electric, 92-UP.

1016386
KING PIN, CC 92-UP
tmp83CA-127.jpg
King pin with spring shackle.
Used On: Club Car gas and electric, 92-UP.

1016389WASHER. KINGPIN. CC 92-UP
o
Spring steel wavy tension washer for king pin (1 required for each side). Measures approximately .780 I.D. x 1.010" O.D. x .18" thick.
Used On: Club Car gas and electric 92-UP (DS).

1016430
GASKET, HEAD, CC 92-UP
Stamped aluminum "crush-type" gasket. Used On: Club Car gas FE290, 92-UP.

1016433-04DC CORD, CROWFOOT YELLOW PLUG
tmp83CA-128.jpg
8-1/2' DC cord with molded yellow housing and 2-prong CROWFOOT plug.
Used On: Club Car; Columbia; Cushman; E-Z-Go; Legend; Melex; Noland; Pargo; Yamaha.
10120641012100
16587-G1

1016436GASKET, ROCKER COVER, CC 92-UP
tmp83CA-129.jpg
Molded black neoprene gasket.
Used On: Club Car gas FE290 and FE350, 92-UP.

1016438GASKET, AIR CLEANER, CC 92-UP
o
Die-cut gasket. Mounts between carbure­tor and intake manifold.
Used On: Club Car gas 92-UP.

1016439GASKET, INSULATOR, CC 92-UP
tmp83CA-130.jpg
Die-cut gasket. Measures approximately 1-3/4" between mount hole centers.
Used On: Club Car gas, 92-UP.

1016440    GASKET, INTAKE, CC 92-UP
o
Die-cut gasket. Measures approximately 1-13/16" between mount hole centers.
Used On: Club Car gas FE290 and FE350, 92-UP,

1016441GASKET, CARBURETOR, CC 92-UP
tmp83CA-131.jpg
Die-cut gasket. Measures approximately 1-13/16" between mount hole centers.
Used On: Club Car gas, 92-UP.

1016446
GASKET, CRANKCASE CVR, CC 92-UP
tmp83CA-132.jpg
Die-cut gasket, 10-hole.
Used On: Club Car gas FE290. 92-UP.

1016447
VALVE, INTAKE, CC 92-UP
Used On: Ctub Car gas FE290, 92-UP.

1016448VALVE, EXHAUST, CC 92-UP
Used On: Club Car gas FE290, 92-UP.

tmp83CA-133.jpg
101645901
PISTON ASSEMBLY, STD, CC 92-UP
Aluminum alloy. Includes rings, piston pin and retainers.
Used On: Club Car gas FE290.92-UP.
Tips: Bofore installing rings on piston, always check to insure that you have the proper end-gap clearance when rings are inserted in cylinder. Consult the manufacturer's maintenance manual for proper specifications and complete installation instructions.

tmp83CA-134.jpg
101645902
PISTON ASSEMBLY, .25MM, CC 92-UP
Aluminum alloy. Includes rings, piston pin and retainers.
Used On: Club Car gas FE290. 92-UR
Tips: Before installing rings on piston, always check to insure that you havo the proper end-gap clearance when rings are inserted in cylinder. Consult the manufacturer's maintenance manual for proper specifications and complete installation instructions.

tmp83CA-135.jpg
101645903PISTON ASSEMBLY, .50MM, CC 92-UP
Aluminum alloy. Includes rings, piston pin and retainors.
Used On: Club Car gas FE290.92-UP.
Tips: Before installing rings on piston, always check to insure that you have the proper end-gap clearance when rings are inserted in cylinder. Consult the manufacturer's maintenance manual for propor specifications and complete installation instructions.

tmp83CA-136.jpg
1016461-01RING SET. STD, CC 92-UP
Set consists of two compression rings and a three-piece oil ring (upper and lower rails with expander).
Used On: Club Car gas FE290, 92-UP.
Tips: Before installing rings on piston, always check to insure that you have the proper end-gap clearance when rings are inserted in cylinder. Consult the manufacturers maintenance manual for proper specifications and complete installation instructions.

tmp83CA-137.jpg
1016461-02              RING SET, .25MM, CC 92-UP
Set consists of two compression rings and a three-piece oil ring (upper and lower rails with expander).
Used On: Club Car gas FE290, 92-UP.
Tips: Before installing rings on piston, always check to insure that you have the proper end-gap clearance when rings are inserted in cylinder. Consult the manufacturers maintenance manual for proper specifications and complete installation instructions.

tmp83CA-138.jpg
1016461-03 RING SET, .50MM, CC 92-UP
Set consists of two compression rings and a three-piece oil ring (upper and lower rails with expander).
Used On: Club Car gas FE290, 92-UP.
Tips: Before installing rings on piston, always check to insure that you have the proper end-gap clearance when rings are inserted in cylinder. Consult the manufacturers maintenance manual for proper specifications and complete installation instructions.

1016467
FILTER, OIL, CC 92-UP (50)
tmp83CA-139.jpg
Spin-on type filter with gasket.
Used On: Club Car gas, 92-UP (OHV engine only): Cushman.

1016478KCARB REPAIR KIT, CC 92-98
tmp83CA-140.jpg
Kit includes: needle valve, springs, float •j?B bowl bolt gasket and o-ring, main nozzle __. and jets.
Used On: Club Car gas, 92-98.

1016491COIL IGNITOR, CC 92-96
tmp83CA-141.jpg
Ignitor coil with extension wire (male and female spade connectors), wire nut and mounting screw.
Used On: Club Car gas, 92-96.

1016492                    COIL IGNITION, CC 92-96
Ignition coil has one male spade terminal. m                       . Used On: Club Car gas, 92-96.
tmp83CA-142.jpg

1016511
RPM LIMITER, CC 92-96
tmp83CA-143.jpg
Sealed electronic unit with three connection leads {bullet, ring terminal and male spade}.
Used On: Club Car gas, 92-96.

1016566SEAL, VALVE STEM, CC 92-UP
tmp83CA-144.jpg
Heat resistant neoprene material with coiled spring around stem hole. Measures approximately .24" (6mm) I.D. x .58" (14.7mm) O.D. x .38" {9.7mm) thick.
Used On: Club Car gas, 92-UR

1016567OIL SEAL, CLUTCH SIDE, CC 92-UP
tmp83CA-145.jpg
For clutch side. Seal measures approximately 1.96" (50mm) O.D. x 1.18" (30mm) I.D. x .23" (6mm) W.
Used On: Club Car gas FE290, 92-UP.

1016568OIL SEAL, FILTER SIDE, CC 92-UP
tmp83CA-146.jpg
Seal measures approximately 1.37" (35mm) O.D x .98" (25mm) I.D. x .27" (7mm) W.
Used On: Club Car gas FE290,92-UP.

1016630
I
OIL WARNING LIGHT, CC 84-UP
tmp83CA-147.jpg
Snap-in unit with two spade connectors. Bezel face measures approximately 3/4" 1-1/4*.
Used On: Club Car gas, 84-UR

1016801WEIGHT KIT. DRIVE CLUTCH, CC 92-UP
Kit includes large centrifugal weights
'4 ^ ^ ^ v W'1^ busn'n9 anc' P'ns ^). small centrifu-£4 I t" *" y,\ \a gal weights with bushing and pin (3), © o o pivot pins (3), plastic washers (6), steel wavy washers <3) steel flat washers (6) and cap screws (6).
Used On: Club Car gas 92-UR

1016810ENGINE MOUNT, CC 84-UP
tmp83CA-148.jpg
Polyurethane mount, molded to factory specifications.
Used On: Club Car gas, 84-UP. 1012290

MUFFLER, CC 92-93
Replacement muffler, compatible with original configuration.
Used On: Club Car gas FE290,92-93 .

1016851REVERSE BUZZER, CC 92-UP G & E
tmp83CA-149.jpg
12/48-volt heavy-duty warning buzzer. Used On: Club Car gas and electric, 92-UP. 10155701015571

1016868BUMPER PAD, FRONT, CC 93-UP
tmp83CA-150.jpg
Rotational-molded high-impact plastic, bolts on like original equipment. Uses P/N 7473 nut.
Used On: Club Car gas and electric 93-UP (OS).

1016876BOLT, BUMPER, REAR, CC 93-UP
tmp83CA-151.jpg
Black anodized shoulder-bolt whh Phillip's head. Measures approximately 2" long with 5/16-18 threads and 3/8' shoulder.Used with P/N 1016379 rear bumper.
Used On: Club Car gas and electric 93-UP (0S>.

1016879
BEZEL, PASS, CC 93-UP
tmp83CA-152.jpg
Injection molded plastic fits in original factory cut outs. Passenger side only.
Used On: Club Car gas and electric, 93-UP.

1016880BEZEL, DRIVER, CC 93-UP
tmp83CA-153.jpg
Injection molded plastic fits in original factory cut outs. Driver side only.
Used On: Club Car gas and electric, 93-UP.

1016952NUT, U, 1/4"-20, CC 93-UP
tmp83CA-154.jpg
1/4-20 thread "clip-on" U-nut. (Used on beverage holders)
Used On: Club Car gas and electric, 93-UP.

1017043-02
SWEATER BASKET, DRIVER, CC 82-UP
tmp83CA-155.jpg
Heavy gauge wire, black vinyl dipped. Measures approximately 8-1/2" x 10-5/16" x 7-1/2" deep. Includes mounting hardware.
Used On: Club Car gas and electric, 82-UR

1017043-04
SWEATER BASKET, PASS, CC 82-UP
 
A ' '
I •. |
\
t
i 4-
1
r •—
1
Heavy gauge wire, black vinyl dipped. Measures approximately 8-1/2" x 10-5/16" x 7-1/2" deep. Includes mounting hardware.
Used On: Club Car gas and electric, 82-UR

1017059 RETAINER,HEADLIGHT BULB CC 93-UP
tmp83CA-156.jpg
Fastens the headlight bulb and harness to the headlight shell.
Used On: Club Car gas and electric, 93-UP.

1017060BULB.HEADLIGHT, CC 93-UP
tmp83CA-157.jpg
12-volt halogen automotive bulb, two filaments. Replacement bulb for P/N 1017061 lens.
Used On: Club Car gas and electric, 93-UP.

1017061
HEADLIGHT LENS, CC 93-UP
Headlight shell, requires P/N 1017060 bulb. Used On: Club Car gas and electric, 93-UP.
tmp83CA-158.jpg

1017062TURN SIGNAL LENS, CC 93-UP
Turn signal lens assembly ONLY! (No bulb or wires.) Black plastic housing with amber lens and two threaded mounting studs. Measures approximately 1-7/8" x 3-5/8". Uses P/N 1011583 replacement bulb.
Used On: Club Car gas and electric, 93-UP.

1017064HEADLIGHT BRACKET, CC 93-UP
tmp83CA-159.jpg
Stainless-steel bracket, measures approximately .75" (19.1 mm) wide and has a .23" 15.9mm) hole in one end. The bracket is bent at an approximate 85-degree angle, 1/2" from the end with no hole.
Used On: Club Car gas and electric, 93-UP.

1017065
RETAINER, HEADLIGHT,CC 93-UP
Fastens the headlight shell to the bezel. Used On: Club Car gas and electric, 93-UP.

1017066HEADLIGHT PIGTAIL, CC 93-UP
tmp83CA-160.jpg
Wiring harness for headlight only.
—'?

1017079BUMPER RETRO KIT. REAR, CC 81-92
tmp83CA-161.jpg
Rotational-molded high-impact plastic New style bumper with hardware adapts to pre 1993 DS models.
Used On: Club Car gas and electric 81*92. 1011093 1011903 1013901

1017083-01
CUP HOLDER, DUAL, CC 93-UP
Dual cup holder with 4 tee holders. Injection molded of black HDPE with fine hair-cell finish. Measures approximately 7" W x 3-1/4" H x 5-a'8" D. Includes mounting hardware. Uses P/N 15041 replacement cap screw.
Used On: Club Car gas and electric, 93-UP. 1016811
tmp83CA-162.jpg
T f

1017266
DELTA A PLATE STRAP, CC 96-UP
Connects driver and passenger "A* plates to shock support tower.
Used On: Club Car gas and electric. 96-UP.

1017434
GASKET, HEAD. 96-UP, FE350
Stamped aluminum "crush-type" gasket. Used On: Club Car gas FE350, 96-UP.

GASKET, CRANKCASE, CC96-UP, FE350
Die-cut gasket, 10-hole.
Used On: Club Car gas FE350,96-UP.

1017444       VALVE, INTAKE, CC 96-UP FE350
frTUsed On: Club Car gas FE350r 96-UR,

1017445
VALVE, EXHAUST, CC 96-UP FE350 Used On: Club Car gas FE350, 96-UP.;

tmp83CA-163.jpg
101744901
PISTON ASSEMBLY, STD, CC FE350
Aluminum alloy. Includes rings, piston pin and retainers.
Used On: Club Car gas FE350. 96-UP.
Tips: Before installing rings on piston, always check to insure that you have the proper end-gap clearance when rings are inserted in cylinder. Consult the manufacturer's maintenance manual for proper specifications and complete installation instructions.

tmp83CA-164.jpg
1017449-02
PISTON ASSEMBLY, .50MM, CC FE350
Aluminum alloy. Includes rings, piston pin and retainers.
Used On: Club Car gas FE350, 96-UP.
Tips: Before installing rings on piston, always check to insure that you have the proper end-gap clearance when rings are inserted in cylinder. Consult the manufacturer's maintenance manual for proper specifications and complete installation instructions.

tmp83CA-165.jpg
1017451-01RING SET, STD, CC FE350
Set consists of two compression rings and a three-piece oil ring (upper and lower rails with expander).
Used On: Club Car gas FE350. 96-UR
Tips: Before installing rings on piston, always check to insure that you have the proper end-gap clearance when rings are inserted in cylinder. Consult the manufacturer's maintenance manual for proper specifications and complete installation instructions.

tmp83CA-166.jpg
1017451-02RING SET, .50MM, CC FE350
Set consists of two compression rings and a three-piece oil ring (upper and lower rails with expander).
Used On: Club Car gas FE350, 96-UR
lips: Before installing rings on piston, always check to insure that you have the proper end-gap clearance when rings are inserted in cylinder. Consult the manufacturer's maintenance manual for proper specifications and complete installation instructions.

FLASHER, 12 VOLT, CC 93-UP
Three-prong flasher unit.
Used On: Universal application where 12-volt turn signal switch is used.

1017503OIL SEAL, CC 96-UP FE350
tmp83CA-167.jpg
For fan side. Seal measures approximately 1.19' (30.2mm) x 1.66" (42.1mm) O.D. x .280 (7.1mm) W.
Used On: Club Car gas FE350, 96-UP.

1017504OIL SEAL, CC 96-UP FE350
tmp83CA-168.jpg
For clutch side. Seal measures approximately 1.32" (33.5mm) x 1.97" (50.1 mm) x.24* (7.1 mm} W.
Used On: Club Car gas FE350. 96-UR

1017682*02
BAGWELL KIT, CC 98-UP
tmp83CA-169.jpg
Plastic liner with installation fasteners.
Used On: Club Car gas and electric 98-UP (OS).

1017911-01
BRAKE DRUM, CC 95-UP
Solid face, no center-hole style. Used On: Club Car 95-UP.
tmp83CA-170.jpg

1017946BRUSH SET. MOTOR, CC 36-48V, YAM 48V
Set of 4 brushes. Measures approximately -3/8" x 9/16" Wx 7/16' thick.
Used On: Club Car electric, 94-UP; Melex; Yamaha 48 volt electric IG19),
tmp83CA-171.jpg
tmp83CA-172.jpg

1017947INSULATOR KIT, CC, CHD# EZ, YAM
Includes two injection molded insulators with dual hex-head holes, two oval fiber
0 O © O insulators with dual .525* I.O holes and
O O O O hardware.
Used On: Club Car electric, 94-UP; Columbia/Harley electric (new style GE motors); E-Z-Go electric (new style GE motors); Yamaha electric, 90-UP (G8, G9, G14,G16).
tmp83CA-173.jpg

COMPUTERS, 48-VOLT REMANUFACTURED
tmp83CA-174.jpg
•AQ
48-volt remanufactured computers for PowerOrive and PowerDrive+ vehicles,
1018006-01
POWERDRIVE
COMPUTER, REMAN, CC 95-97 PD NO CON
$139.90 um ea
PowerOrive with NO onboard connector. Includes 42* cable.
Used On: Club Car electric, 95-97. 1018008-06

COMPUTERS, 48-VOLT REMANUFACTURED
tmp83CA-175.jpg
48-voit remanufactured computers for PowerDrive and PowerDrive+ vehicles.
1018006-03
POWERDRIVE PLUS
COMPUTER. REMAN. CC 95-97 PD+ NO CON
S 159.90 umea
PowerDrive+ with NO on board connector. Includes 42" cable.
Used On: Club Car electric, 95-97. 1018006-08

1018030-01BATTERY HOLD DOWN, CC 48V, 95-UP
Extruded, black plastic hold down with two 5/16" holes. Measures approximately 10-1/4M long.
Used On: Club Car 48-volt electric, 95-UP

1018057-01CHOKE BUTTON, CC 98-UP
tmp83CA-176.jpg
Injection molded of black plastic. Three* piece unit consists of outer guide ring, cen­ter plunger and coiled spring. Has "CHOKE" embossed on outer ring.
Used On: Club Car gas 98-UP (DS).

1018593-01
MUFFLER, CC 94-UP
Replacement muffler, compatible with original configuration.
Used On: Club Car gas FE290, 94-UP. 1017491
tmp83CA-177.jpg

1018693-02BRUSH SET. GENERATOR, CC 97-UP
r f r i Set of 4 brushes. Measures approximately
*? M MM ,. L x 1/2.. w
Used On: Club Car gas, 97-UR

1018800-01BELLOWS. STEERING, DVR, CC 97-UP
tmp83CA-178.jpg
Rubber boot keeps dirt, dust and grass out of your steering rack.
Used On: Club Car gas and electric, 97-UP driver side.

1018802-01BALL JOINT, INNER, CC 97-UP
tmp83CA-179.jpg
Inner steering rack joint.
Used On; Club Car gas and electric, 97-UP.

1019092-01              COIL, IGNITION, CC 97-UP
/ B^Hrs^ Ignition coil has one male spade terminal. / ^^* Used On: Club Car gas, 97-UP.

1019094-01
RPM LIMITER, CC 97-UP
Sealed electronic unit with three connection leads (two insulated female bullet-type and one ring terminal type).
Used On: Club Car gas, 97-UR

tmp83CA-180.jpg
T-i-A \ „**
48-volt remanufactured computers for PowerOrive and PowerDrive+ vehicles.
1019099-01
POWERDRIVE
COMPUTER, REMAN, CC 98-UP PD 3PIN $139.90 umea
PoworDrive with a 3-pin connector. Includes 6' cable.
Used On: Club Car electric, 98-UP.

tmp83CA-181.jpg
1019167-01
BELT GENERATOR, CC 97-UP
Reinforced belt. Measures approximately 1/2" W x 36-1/2" O.D.
Used On: Club Car gas, 97-UP (OHV).

1019278-01
BEARING, INPUT SHAFT, CC GOO-UP
tmp83CA-182.jpg
Ball bearing, open both sides. Measures approximately .98" (24.9mm) I.D x 2.44" (62mm) O.D.x.67 (16.9mm) W.
Used On: Club Car gas, 00-UR

1019330-01SPRING, BRAKE RETURN, CC 87-98GS
Tension-type, twenty-coil spring. Measures approximately 3-7/8" long.
Used On: Club Car gas, 87-98. 1010935 1013532 1013569

1019540-01BRAKE PEDAL KIT, CC 81-UP
Includes brake pedal weldment, pedal pad, return spring, rods and hardware.
- * - Used On: Club Car gas and electric, 81-UP.
tmp83CA-183.jpg
1011406

1019644-01RESISTOR, ENERGY DISPLACE, CC 98-UP
tmp83CA-184.jpg
6-coil resistor for use on P/N 1018836-01, 48-volt solenoid.
Used On: Club Car electric, 98-UP.

1020260-01ACCELERATOR PIVOT ROD, CC 96-UP
tmp83CA-185.jpg
Plated for corrosion protection. Threaded, knurled rod measures approximately .50" (12.7mm) D x 6.50" {165.1mm> L
Used On: Club Car gas and electric, 96-UP. 1017325

1032 BUSHING, HILL BRAKE PIVOT, CC
tmp83CA-186.jpg
Nylon flange-type bushing. Measures approximately .37" (9.5mm) I.D. x .50" (12.7mm) O.D. x .25" (6.4mm) W. Flange measures approximately .75" (19mm) O.D. x .06* (15mm) W.
Used On: Club Car gas and electric, 80-UR

108
LIGHT KITf RECESSED, CC 81-92
Includes a pair of rectangular halogen headlights, amber front running lights, red rear tail lights, wiring, connectors, switch and complete installation instructions.
Molded of black, high-impact ABS plastic. Used On: Club Car gas and electric, 81-92.
tmp83CA-187.jpg
tinmm
didkkfcU

tmp83CA-188.jpg
108ABEZEL & HEADLIGHT, CC 81-92
Includes a pair of rectangular halogen headlights with left and right bezels. Does NOT include wiring harness, tail lights, amber-front runners, or connectors.

108L
BEZEL DRIVER. CC 81-92
tmp83CA-189.jpg

108R
BEZEL PASS. CC 81-92
tmp83CA-190.jpg

109SWITCH, TOGGLE
tmp83CA-191.jpg
"On-Off" type switch with two spade terminals, knurled nut, pal nut and indexed "ON/OFF" position plate.
Used On: Universal application on many golf cars and other vehicles.

122B
SCUFF GUARD, PAIR CLUB CAR BLK SET
Formed from tough high-density polyethylene with hair-celt texture. Color: Black.
Used On: Club Car gas and electric, 81-UR
tmp83CA-192.jpg

12305-G1RETAINING RING, CC, CHD, EZ
tmp83CA-193.jpg
Push type zinc plated clip for retaining brake cables.
Used On: Club Car gas and electric, 81-UP; Columbia/Harley gas and electric, 86-UP; Cushman; E-Z-Go gas and electric, 68-UP; Legend; Jacobsen.
10117797647644

12394-G1
GASKET, EXHAUST, CC, EZ
tmp83CA-194.jpg
Composition gasket pressed between aluminum            jackets.            Measures
approximately 2-5/16" between mount hole centers.
Used On: Club Car gas, 84-91 (muffler to header pipe only); E-Z-Go 2-cycle gas, 76-94 (Marathon).
1012510
1015450

13141-G1
MICRO SWITCH, CC, EZ (20)
Plunger-style with three terminals (N.O., N.C., COM.).
Used On: Club Car gas and electric with lights, 81-UP; E-Z-Go gas and electric, 71-82; Otis.
1011439
tmp83CA-195.jpg

13164G1CIRCUIT BREAKER, 12V-50A
tmp83CA-196.jpg
Self-resetting circuit breaker with stud type terminals. 12-volt, 50-amps.
Used On: Club Car/Lester battery chargers; ColumbiafHarley; E-Z-Go battery chargers.
1012005 1012450 11573-G1 13163-G1 66058-65

13270-G1SHOCK, REAR, CC, EZ
Bushing mount on one end; threaded 38-24 shaft on other. Compresses to 10-1/4"; extends to 13-1/4", measured from end to end. Uses 1 P/N 944 bushing kit (NOT included).
Used On: Club Car gas, 84-96; E-Z-Go electric, 79-94 |3 and 4-wheel).
1011085 1011414 1012781 1014234

14608-G1REVERSE BUZZER, CC, CHD, EZ
24/36-volt heavy-duty warning buzzer. (Not the same configuration as OEM buzzer).
Used On: Club Car electric, early 70-UP; Columbia/Harley; Cushman; E-Z-Go electric, 65-83, Legend; Melex; Noland.
1010051
tmp83CA-197.jpg

36-48V. 350A. W/D
15194
Solid state electronic speed controllers.
(W/D) Equipped with "disable" feature which helps prevent the rear wheels from spinning during rapid acceleration.
(WO/D) Not equipped with "disable" feature.
NEW

24-36V, 400A, W/D {Adjustable} 15199
Solid state electronic speed controllers.
(W/D) Equipped with "disable" feature which helps prevent the rear wheels from spinning during rapid acceleration.
(WO/D) Not equipped with "disable" feature.
NEW

15200FOOT SWITCH, CURTIS FP-2
Io
Eliminates adapting existing throttle pedal to work with pot box.
Used On: Universal assembly for use with electronic speed controllers.

15201INSULATOR, ADVANCED DC MOTOR
tmp83CA-198.jpg
Fiber insulator washer. Measures approximately 5/16* I.D. x 1" O.D. x .5/32" thick.
Used On: Club Car electric {Advanced motors); E-Z-Go electric, 97-UP (Advanced motors).

15202INSULATOR, ADVANCED DC MOTOR
tmp83CA-199.jpg
Square plastic insulator with shoulder. Square shoulder measures approximately .92" (23.3mm) x .92" (23.3mm). Largest diameter on round step-shoulder measures approximately .54" 0.0 (13.7mm) x .20" (5.2mm) L. Smallest diameter on round step-shoulder measures approximately .50" (12.7mm) x .09" (2.3mm) L. Hole I.D. is approximately .33" (8.4mm).
Used On: Club Car electric (Advanced motors); E-Z-Go electric, 97-UP (Advanced motors).

15203MOTOR, 36-48V, 4HP, 10SP, CC, YAM
tmp83CA-200.jpg
36'48-volt, 4 HP, 10-spline motor.
Used On: Club Car electric, 84-UPj Yamaha electric, 89-93 1/2.

15206SAND BUCKET LID, CLUB CAR
Clear acrylic plastic top for OEM sand buckets. Measures approximately 8-5/8" x 10-1/4". Requires two small plastic cable ties to install (Ties not included).
Used On: Club Car gas and electric, 82-99.

15207
LEAF SPRING, FRONT, HD, CC
Heavy-duty front leaf spring, painted. Measures approximately 27" between centers of bushing holes.
Used On: Club Car gas and electric, 81-UP.

36-48V, 275A, W/D
15299
Solid state electronic speed controllers.
(W/D) Equipped with "disable" feature which helps prevent the rear wheels from spinning during rapid acceleration.
(WO/D) Not equipped with "disable" feature.
NEW

VOLTAGE REDUCER, 16-18V TO 12V
tmp83CA-201.jpg
Reduces input voltage from 16-18 volts DC down to 12 volts DC, 15-amps.
Used On: Miscellaneous applications for golf cars and utility vehicles.
Use P/N 15950 for
48 volt systems for best results
Tips: Some larger motors and controllers may reduce the input voltage which may temporarily reduce the output voltage on takeoff. For these applications, you may want the 48v to 12v voltage reducer, P/N
15950.

15318VOLTAGE REDUCER, 48-12 VOLT
tmp83CA-202.jpg
Reduces 48-volts DC down to 12-volts DC, 10-amps.
Used On: Miscellaneous applications for golf cars and utility vehicles.

15324GEARS. HIGH SPEED, CC E84-97
tmp83CA-203.jpg
58-tooth helical-cut gear, with matching 30-tooth pinion gear.
Used On: Club Car electric, 84-97.

15325GEARS, HIGH SPEED, CC G97-UP
O
76-tooth helical-cut gear, with matching 23-tooth pinion gear.
Used On: Club Car gas, 97-UP.

15374WIRING KIT FOR 4 LIGHTS
Kit includes 30-amp relay (1), snap-lock connector (1), and illuminated 3-terminal rocker switch (1). Mounting hardware includes the following wire: 43" black with fuse holder (1), 43" red wire (1). 40" blue (1), 40- green (1), and 9-1/2" white (2).
Used On: Adaptable to most light kits from any manufacturer.

COMPUTERS, 48-VOLT REMANUFACTURED
tmp83CA-204.jpg
48-voit remanufactured computers for PowerDrive and PowerDrive+ vehicles.
POWERDRIVE PLUS
COMPUTER, REMAN, CC 95-96 PD+ 4PIN $179.90 uuu
PowerOrive-f with a 4-pin connector. Includes 26' cable..
Used On: Club Car electric, 95-96. (Prior to
SOriiil# 9615-494279).

36-48V, 450A, WO/D 15421
Solid state electronic speed controllers.
(W/D) Equipped with "disable" feature which helps prevent the rear wheels from spinning during rapid acceleration.
(WO/D) Not equipped with "disable" feature.
NEW

36-48V, 550A, W/D 15422
Solid state electronic speed controllers.
(W/D) Equipped with "disable" feature which helps prevent the rear wheels from spinning during rapid acceleration.
(WO/D) Not equipped with "disable" feature.
NEW

36-48V. 550A, WO/0
15423
Solid state electronic speed controllers.
(W/D) Equipped with "disable" feature which helps prevent the rear wheels from spinning during rapid acceleration.
(WO/D) Not equipped with "disable" feature.
NEW

15426
POTENTIOMETER. CURTIS 98191
tmp83CA-205.jpg
Used with Curtis pot box.
Used On: Club Car; Columbia/Harley; Cushman; E-Z-Go electric, 89-94 (Marathon); Melex.

BEARING, 6008
tmp83CA-206.jpg
Ball bearing, open both sides. Measures approximately 1.57" (39.9mm) I.D. x 2.68" 168.1mm) O.D. x .58" <14.9mm) W.
Used On: Club Car electric, 84-UP; Cushman; E-2-Go 4-cycle gas, 91-UP; Noland; Pargo; Yamaha electric. 79-92 <G1, G2, G8,1992 and earlier, G9).
10137787330

tmp83CA-207.jpg
BEZEL & HEADLIGHT.CC 93-UP
VERTICALLY ADJUSTABLE! Includes a pair of rectangular halogen headlights, amber front running lights, and complete installation instructions. Does NOT include wiring harness, tail lights, or connectors.

15708
LIGHT KIT, RECESSED, CC 93-UP
VERTICALLY ADJUSTABLE! Includes a pair of rectangular halogen headlights, amber front running lights, red rear tail lights, wiring harness, connectors, switch and complete installation instructions.
Molded of black, high-impact ABS plastic. Used On: Club Car gas and electric, 93-UP.
tmp83CA-208.jpg

15726
CLUTCH, DRIVEN, CC 97-UP
tmp83CA-209.jpg
Die cast unit, machined and balanced. Used On: Club Car gas, 97-UP. 1018340-01

KEY SWITCH. CC G96UP
Switch only. Uses P/N 1012505 key. Used On: Club Car gas. 96-UP. 1018263-01

15728KEY SWITCH, CC E96-UP
tmp83CA-210.jpg
Switch only. Uses P/N 1012505 key. Used On: Club Car electric, 96-UP. 1018262-01

15730ACCESS PANEL CC 84-UP
tmp83CA-211.jpg
Injection molded, black plastic.
Used On: Club Car gas and electric 84-UP (DS).
10130321015829-02

15731PULLER. DRIVE CLUTCH. CC 84-87
For removing Salsbury style drive clutch from crankshaft.
Used On: Club Car gas, 84-87 and aftermarket Salbury clutch 88-96.
1012803

15734STEERING WHEEL, CC 92-UP
tmp83CA-212.jpg
Steering wheel only. Uses P/N 15735 scorecard holder.
Used On: Club Car gas and electric, 92-UP. 1016156

15735 SCORECARD ASSEMBLY, CC 92-UP
tmp83CA-213.jpg
Injection molded from black plastic and includes tension clip with pencil holder.
Used On: Club Car gas and electric. 92-UP. 1016219

15736SHACKLE, REAR SPRING, CC G84-UP
S-shaped, stamped steel black shackle. Measures approximately 6-1/2" L, 1-1/4" W and 1/4" T, with a 3/8" hole drilled at each end, approximately 5-1/2* between centers.
Used On: Club Car gas, 84-UP. 1012304

15740F & R SWITCH, 48V, POWERDRIVE, CC 96-UP
tmp83CA-214.jpg
Complete switch, less handle. Includes 3 micro switches and installation instructions.
Used On: Club Car 48-volt electric, 96-UP
(PowerDrive).
1017530-05

15741F & R SWITCH, 36V & 48V, CC 90-95
tmp83CA-215.jpg
Complete switch, less handle. Includes 3 micro switches and installation instructions.
Used On: Club Car 36-voft electric, 90-94; Club Car 48-volt electric, 95.
1017530-04

15742                        F & R LIMIT SWITCH. CC 99-UP
Lever-type switch with three-wires (two insulated male spades for COM and NO, one deactivated on NC).
Used On: Club Car gas and electric, 99-UP. 1019791-01

15743V GLIDE SWITCH CASE, CC 88-UP
tmp83CA-216.jpg
Black piastic housing with eight mounted copper contacts and one brass pivot
bushing. •0
Used On: Club Car electric, 88-UP.
1014999

15744
V GLIDE SWITCH, 48V, CC 95
Speed switch assembly with five-wires, six connectors. {Three female spade connectors, one male bullet connector and two female connectors.) Includes actuator lever with ball stud connector.
Used On: Club Car 48-volt electric, 95. 1016012
tmp83CA-217.jpg

GLIDE SWITCH, 36V, CC 88-UP
tmp83CA-218.jpg
Speed switch assembly with two wires. (One male bullet connector and one ring terminal connector.) Includes actuator lever with ball stud connector.
Used On: Club Car 36-volt electric with resistor coils, 88-UP. DOES NOT WORK WITH SOLID STATE SPEED CONTROLLER.
1016140

15746SPEED SWITCH ASSEMBLY, CC 80-88
tmp83CA-219.jpg
Five micro switches actuated by plastic ramp slide, all secured inside square aluminum tubing sealed at each end with plastic cap. Includes ball stud connector.
Used On: Club Car electric, 80-88. 1013410

15747                   MICRO SWITCH, POTENTIOMETER, CC 96-97
tmp83CA-220.jpg
Lever-type switch with two spade terminals (C, NO).
Used On: Club car 48-volt electric, 96-97. 1017830

15748POTENTIOMETER W/GRAY PLUG, CC 96-97
tmp83CA-221.jpg
Potentiometer assembly with flexible harness and moisture resistant snap-on plug. Includes actuator lever, micro switch and plastic bushing.
Used On: Club Car 48-volt electric, 96-97 Cars with serial number 9628-508740-UR
1017392-01

15749
POTENTIOMETER MULTISTEP, CC 01-UP
Potentiometer assembly with three-wire moisture resistant snap-on plug, one wire with female spade connector and one wire with male bullet connector. Includes actuator lever with ball stud connector.
Used On: Club Car 48-volt electric, 01-UP. 1019320-01
tmp83CA-222.jpg

15751POTENTIOMETER MULTISTEP, CC 98-99
tmp83CA-223.jpg
Potentiometer assembly with 6 pin square moisture resistant snap-on plug. Includes actuator lever, micro switch and plastic bushing.
Used On: Club Car 48-vo(t electric, 98-99. 1019320-03

15752GUIDE RING, CC 94-99
tmp83CA-224.jpg
Guide ring inserts into driven end of armature.
Used On: Club Car electric, 94-99. 1017891-01

15753
FUSE & RECEPTACLE KIT, CC 95-UP
tmp83CA-225.jpg
Injection molded black plastic receptacle housing with 3-prong female plug. Includes mounted clear plastic covered fuse link (1), 3/8-amp type AGC in-line fuse (1), moisture resistant in-line fuse holder (1) and installation instructions.
Used On: Club Car 48-volt electric, 95-UP. 1018021-01

36-48V, 275A, WO/D
15760
Solid state electronic speed controllers.
(W/D) Equipped with 'disable' feature which helps prevent the rear wheels from spinning during rapid acceleration.
(WO/D) Not equipped with "disable" feature.
REBUILT

48V 225A
15761
Solid state electronic speed controllers.
(W/D) Equipped with "disable" feature which helps prevent the rear wheels from spinning during rapid acceleration.
(WO/D) Not equipped with "disable" feature.
REBUILT

48V 230A
15762
Solid state electronic speed controllers.
(W/D) Equipped with "disable" feature which helps prevent the rear wheels from spinning during rapid acceleration.
(WO/D) Not equipped with "disable" feature.
REBUILT

15764MOTOR, CC, YAM
tmp83CA-226.jpg
36/48-volt, 3 or 4 HP, 10-spline motor. (3 HP on 36-volt systems @2820 rpm; 4 HP on 48-volt systems @ 4250 rpm)
Used On: Club Car 36-volt electric, 84-UP; Yamaha 36-volt electric, 89-93 1/2 (G2, G8, G9).

BRUSH HOLDER, CC, EZ, YAM
tmp83CA-227.jpg
Insulated brush holder with tension springs. Includes rubber mount grommets and screws.
Used On: Club Car electric, 94-UP; E-Z-Go electric, 94-96; Yamaha 36-volt electric. 92-00 (G8. G9. G14, G16).                          '
1017948

15799MUFFLER, CC 96-UP, FE350
tmp83CA-228.jpg
Replacement muffler, compatible with original configuration.
Used On: Club Car gas FE350, 96-UP. 1018594-01

15809MOTOR, 36V-7HP, 48V-11HP, CC 96-UP
tmp83CA-229.jpg
36/48-volt, 7 or 11 HP, 10-spline motor. (7 HP on 36-volt systems; 11 HP on 48-volt systems)
Used On: Club Car electric, 36 and 48-volt, 96-UP.

15810GASKET, EXHAUST, CC 96-UP, FE350
O
Die-cut gasket. Measures approximately 1-7/8" between mount hole centers.
Used On: Club Car gas FE350, 96-UP. 1016904

15811 REVERSE BUZZER, CC, CHD, EZ
tmp83CA-230.jpg
J
9/36-volt buzzer in black plastic housing r with two male spade connectors. Mount tab has two 5/32" holes, approximately 2" between centers.
Used On: Club Car electric, early 70-UP; Columbia/Harley; Cushman; E-Z-Go electric, 65-UP; Legend; Melex; Noland.

15812CABLE END, TRANSMISSION, CC
tmp83CA-231.jpg
Quick connect ball joint end with #10-32 threads.
Used On: Club Car gas, 84-UP. 1012333

15813
ACCELERATOR ROD, CC G98-UP
Zinc plated rod. 18-1/8" long with 1/4-28 threads each end. Includes 1/4-28 jam nuts (2) and P/N 15814, ball joint ends (2).
Used On: Club Car gas, 98-UP. 1019124-01

15814ACCELERATOR ROD END, CC 98-UP
tmp83CA-232.jpg
Quick connect ball joint end with 1/4-20 threads. Used on P/Ns 15813 and 15815, accelerator rod assemblies.
Used On: Club Car gas, 98-UP. 1011734

ACCELERATOR ROD. CC G97. E96-UP
Zinc plated rod, 16-1/8" long with 1/4-28 threads each end. Center of rod has a 3/4" step, approximately 7" long. Includes 1/4-20 jam nuts (2) and P/N 15814, ball joint ends (2).
Used On: Club Car gas 97 and electric 96-UP.
1018719-01

15845BRUSH HOLDER, CC, EZ
Insulated brush holder with tension springs.
Used On: Club Car electric; E-Z-Go electric, 97-UP (Advanced DC Motor only).

15846
CLUTCH, DRIVE, CC 97-UP
tmp83CA-233.jpg
Clutch assembly including fixed sheave and starter-generator pulley. (5000 RPM max!
Used On: Club Car gas, 97-UP. 1018339-02

15847STEERING GEAR BOX, CC 84-UP
Rack and pinion style gear box.
Used On: Club Car gas and electric, 84-UP.
1018783-02

24-36V, 275A, WO/D
15911
Solid state electronic speed controllers.
(W/D) Equipped with 'disable' feature which helps prevent the rear wheels from spinning during rapid acceleration.
(WO/D) Not equipped with "disable" feature.
REBUILT

36-48V, 275A, W/D 15912
Solid state electronic speed controllers.
(W/D) Equipped with 'disable' feature which helps prevent the rear wheels from spinning during rapid acceleration.
(WO/D) Not equipped with "disable" feature.
REBUILT

24-36V, 400A, W/D {Adjustable) 15914
Solid state electronic speed controllers.
(W/D) Equipped with 'disable' feature which helps prevent the rear wheels from spinning during rapid acceleration.
(WO/D) Not equipped with "disable" feature.
REBUILT

36-48V, 350A. W/D
15917
Solid state electronic speed controllers.
(W/D) Equipped with "disable" feature which helps prevent the rear wheels from spinning during rapid acceleration.
(WO/D) Not equipped with "disable" feature.
REBUILT

36-48V, 550A, W/D
15923
Solid state electronic speed controllers.
(W/D) Equipped with "disable" feature which helps prevent the rear wheels from spinning during rapid acceleration.
(WO/D) Not equipped with "disable" feature.
REBUILT __

48V 230A
15924
Solid state electronic speed controllers.
(W/D) Equipped with "disable" feature which helps prevent the rear wheels from spinning during rapid acceleration.
(WO/D) Not equipped with "disable" feature.
REBUILT

15930FILTER. AIR, CC, CHD, EZ
tmp83CA-234.jpg
Layered paper-type element with an inner and outer wire mesh encasement, and sealed end caps. Measures approximately 6-1/4" H x 4-1/4' O.D.
Used On: Club Car gas, 84-91; Columbia/ Harley 2-cycle gas, 68-95; E-Z-Go 2-cycle gas, 76-94 (Marathon).
10125061013379

CARBURETOR, CC 84-91
Float bowl style carburetor with linkage
^^_ __ rod and gaskets.
ifO
Used On: Club Car gas, 84-91.
O
1014541
tmp83CA-235.jpg

CARBURETOR, CC. 92-97 FE290
Float bowl style carburetor - 32300 body style.
Used On: Club Car gas, 92-97. 1016478

15933CARBURETOR, CC 98-UP FE290
tmp83CA-236.jpg
Float bowl style carburetor - 32670 body style.
Used On: Club Car gas, 98-UP. 1019056-01

15934CARBURETOR, CC 96-UP FE350
Float bowl style carburetor • 32740 body style.
Used On: Club Car gas, 96-UP. 1019059-01

15935 COLLET, VALVE, CC 92-UP
tmp83CA-237.jpg
Retainer for valve stem. Two required per vaive.
Used On: Club Car gas, 92-UP. 1016450

15936CRANKSHAFT, FE290, CC 92-96
tmp83CA-238.jpg
Balanced crankshaft assembly with helical gear, spur gears and connecting rod assembly for counter balance weight.
Used On: Club Car gas, 92-96 (Counter clockwise).
1016468

15937CONNECTING ROD, CC, STD, FE290
tmp83CA-239.jpg
Cast aluminum rod.
Used On: Club Car gas, 92-UP.
1016475-01

15938CONNECTING ROD, .50, CC, FE290
tmp83CA-240.jpg
Cast aluminum rod.
Used On: Club Car gas, 92-UP.
1016475-02

15939FUSE, POWERDRIVE, CC 95-UP
tmp83CA-241.jpg
Clear plastic covered fuse link with two #10-32 studs. Includes installation instructions.
Used On: Club Car 48-volt electric, 95-UP. 1017968-01

CABLE, GOVERNOR, CC 97UP
Flexible metal vinyl covered housing and an additional braided nylon outer sheath, with stranded stainless-steel inner cable. Approximate measurements: Housing: 14-1/4°; Cable, including clevises: 20-3/8*.
Used On: Club Car gas, 97-UP. 1018324-01

CABLE, ACCELERATOR, CC 97-UP
Flexible metal vinyl covered housing with stranded stainless-steel inner cable and an extra 19-3/4* rubber protective sheath on "snubber" spring end. Approximate measurements: Housing : 31-1/2". Cable: 37"
Used On: Club Car gas, 97-UP. 1018325-01

15942STARTER GENERATOR, CC 97-UP
tmp83CA-242.jpg
Mando style starter-generator with unpainted zinc plated frame.
Used On: Club Car gas, 97-UP. 1018337-01
tmp83CA-243.jpg

15944CONTROLLER, POWERDRIVE +, CC 96-97
tmp83CA-244.jpg
48-volt, 225-amp solid-state electronic speed controller.
Used On: Club Car 48-volt electric, 96-97 (PowerDrive+).
1018537-01

15945CONTROLLER, POWERDRIVE +, CC 98-UP
tmp83CA-245.jpg
48-volt, 220-amp solid-state electronic speed controller.
Used On: Club Car 48-volt electric, 98-UP (PowerDrive+).
1018879-01

15946CRANKSHAFT, FE290, CC 97-UP
tmp83CA-246.jpg
Balanced crankshaft assembly with helical gear and spur gears.
Used On: Club Car gas, 97-UP (Clockwise). 101922301

tmp83CA-247.jpg
15947
CABLE, F & R, CC 98-UP
Flexible metal vinyl covered housing, stranded stainless-steel inner cable with snap-socket connectors on each end. Metal sleeve on one housing end has an approximate 90-degree bend. Two required per car.
Used On: Club Car gas, 98-UP. 1019515-01

BRAKE EQUAUZER ROD, CC 98-UP
Zinc plated rod with pivot hole on one end and 5/16-18 threads on other. Has a 1/8" drilled hole on threaded end for brake return spring connection. Approximate overall length is 9/1/4"
Used On: Club Car gas and electric, 98-UP. 1019531-01

15949MICRO SWITCH, CC 99-UP
Lever-type switch with three spade terminals (N.O., N.C., COM.). Used on F/B switch assembly to control half speed.
Used On: Club Car 48-volt electric, 99-UP (PowerDrive).
1019771-01

"Cc
CABLE, BRAKE, CC 00-UP
Flexible metal vinyl covered housing with stranded steel inner cable, and sealing boots on each end. Approximate measurements: Housing: 33"; Cable, including clevis 41-7/8*. An extra 16" abrasion protection sheath is positioned over the housing on the clevis end.
Used On: Club Car gas and electric, 00-UP. 1020221-01

16022RETAINING RING, CC 92-UP
C
Retainer "E" clip for governor and throttle cables.
Used On: Club Car gas, 92-UP. 1016202

16025PLATE, PASSENGER, CC 82-92
tmp83CA-248.jpg
Includes P/N 1015583 urethane bushings (2), P/N 7719 bronze bushings (2) and grease fitting (1).
Used On: Club Car gas and electric. 82-92. 1015586

16026DRAG LINK. CC 84-UP
tmp83CA-249.jpg
Connects rack end to tie rod end.;
Used On: Club Car gas and electric, 84-UP (S/N8411-52367-UPK
1012467

16027A PLATE, DRIVER, CC 82-92
tmp83CA-250.jpg
Includes P/N 1015583 urethane bushings (2), P/N 7719 bronze bushings (2) and grease fitting (1).
Used On: Club Car gas and electric, 82-92. 1015589

16028 SHACKLE, REAR SPRING, CC E80-UP
Stamped aluminum flat bar with two 3/8" holes drilled 5' between centers. Measures approximately 1/4* x 1-3/16" x 6"
Used On: Club Car electric, 80-UP. 7569

16029SPRING, BRAKE SHOE, CC, CHD, EZ, YA
tmp83CA-251.jpg
"U-shaped" spring steel retainer for brake shoes. NOT FOR USE ON BENDIX BRAKE SYSTEM.
Used On: Club Car gas and electric. 81-UP; Columbia/Harley gas and electric, 86-94; E-Z-Go gas and electric, 81-96; Yamaha gas and electric, 78-91 (G1, G2, G8, G9).
1011466

16030 DUST COVER. BRAKE, CC, CHD, EZ. YAM
Molded neoprene cover for bralce actuator. NOT FOR USE ON BENDIX BRAKE ~~ SYSTEM.
Used On: Club Car gas and electric, 81-UP; Columbia/Harley gas and electric, 86-94; E-Z-Go gas and electric, 81-96; Yamaha gas and electric, 78-91 (G1. G2. G8, G9).
1010850

16105MOTOR, 5HP, CC, YAM 10 SPLINE
tmp83CA-252.jpg
36-volt, 5 HP, 10-spline high speed motor.
Used On: Club Car electric, 36-volt, 84-95; Yamaha electric, 88-94 <G2, G8, G9, G14).

16106
MOTOR, 2HP, CC, YAM 10 SPLINE
tmp83CA-253.jpg
36-volt. 2.5 HP, 10-spline motor.
Used On: Club Car electric, 36-volt, 96-UP; Yamaha electric. 88-94 <G2, G8, G9. G14).

16118
KING PIN. CC 81-92
tmp83CA-254.jpg
King pin with spring shackle.
Used On: Club Car gas and electric, 81-92.
1010121

16132
COUPLER, 10 SPLINE CC, EZ
Hardened steel coupling for repairing damaged splines on motor input shaft.
Used On: Club Car electric, 81-85; E-Z-Go electric, 71-85.
tmp83CA-255.jpg

16136F & R SWITCH, POWERDRIVE+, CC 98-UP
tmp83CA-256.jpg
Plastic "snap-in" switch with rocker-type selector and six male spade terminals. Selects F & R and Tow/Run positions.
Used On: Club Car 48-volt electric, 98-UP (PowerDrive+).
1018560-01

tmp83CA-257.jpg
POTENTIOMETER UPDATE KIT, CC 96-97
Kit includes motor controler output regulator, drive bar, accelerator bracket and bearing assembly, adapter plug assembly, adapter harness, tie wrap, three-pin wedge lock, pivot rod weldment, hex head screw, nylon lock nut, accelerator spacer, male bullet terminal insulated male quick disconnect terminal and three-pin plug-Used On: Club Car 48-volt electric, 96-97. Cars with serial number 9628-508739-DOWN.
1017392-02

tmp83CA-258.jpg
POTENTIOMETER, MULTISTEP, CC 00
Potentiometer assembly with three-wire moisture resistant snap-on plug, one wire with female spade connector and one wire with male bullet connector. Includes actuator lever with ball stud connector.
Used On: Club Car 48-volt electric, 2000. 1019320-04

16139
RETAINING RING. CC 86-96
Retaining ring for outer axle tube bearing. Used On: Club Car gas and electric. 86-96. 1013792
tmp83CA-259.jpg

BRUSH COVERS, STARTER. CC. CHD. E2.YAM
tmp83CA-260.jpg
Molded rubber "snap-in* cover for brush access openings.
Used On: Club Cor gas, 84-UP; Columbia/ Harley 2-cycle gas, 67-95; E-Z-Go gas, 80-UP; Yamaha gas, 78-UP {G1, G2,*G3, G5, G8, G9, Gil. G14, G16, G20, G21, G22).
16894-G1 26887-G1 26888-G01

tmp83CA-261.jpg
I
I \
All Trax solid-state programmable elec­tronic speed controller will replace Curtis style 1204 unit. Sealed and completely waterproof.
16387CONTROLLER. 36V 300A, CC 90-94

tmp83CA-262.jpg
i
t \
All Trax solid-state programmable elec­tronic speed controller will replace Curtis style 1204 unit. Sealed and completely waterproof.
16388CONTROLLER, 48V 300A, CC 96-UP

u-u
All Trax solid-state programmable elec­tronic speed controller will replace Curtis style 1204 unit. Sealed and completely waterproof.
16390CONTROLLER, 48V 400A, CC 96-UP

tmp83CA-263.jpg
i
I \
All Trax solid-state programmable elec­tronic speed controller will replace Curtis style 1204 unit. Sealed and completely waterproof.
16391CONTROLLER, 36V 400A, CC 90-94

16917-G1BRUSH SET, MOTOR, CC, CHD, EZ, HYU
tmp83CA-264.jpg
Set of 4 brushes (with studs) for GE motors. Measures approximately 1-7/16" L x 5/8" W, 1/2' thick.
Used On: Club Car electric, 80-93; Columbia/Harley electric, 86-90; Cushman electric; E-Z-Go electric, 80-92; Hyundai electric; Legend; Nordskog; Taylor Dunn.
10112821011410

16920-G1BUCKLE, BAG STRAP, CC, CHD, EZ
tmp83CA-265.jpg
Made of black high impact nylon to prevent rust and corrosion.
Used On: Club Car 81-UP; Columbia/Harley 84-UP; E-2-Go 76-94 (Marathon); Legend.

17290-G1SPRING. BRAKE SHOE, CC, EZ, YAM
17-coil spring. Measures approximately 3-3/4" long.
Used On: Club Car gas and electric, 80-UP; Columbia/Harley, gas and electric, 86-UP; E-Z-Go gas and electric. 87-1/2-96; Hyundai gas and electric, 90-UP; Jacobsen; Legend electric; Yamaha gas and electric, 79-92 (G1, G2, G8. G9).
10113141011464

17429-G1BRAKE SHOES, CC, CHD, EZf YAM
tmp83CA-266.jpg
Bonded lining measures 1-3/16" W x 6" L.
Used On: Club Car gas and electric, 81-94; ColumbiaVHarley gas and electric, 86-89; gas and electric, 82-86 1/2; Legend; Yamaha gas and electric, 78-81 {G1).
10112961011463

18436-G1RIVET, DRIVE
tmp83CA-267.jpg
Plastic rivet with center drive pin.
Used On: Universal application on many golf cars and industrial vehicles.

203                    RIVET, DRIVE, BLACK, 1'
Plastic rivet with center drive pin. Approximate measurements: Head 5/8" D, body 1/4" D, stem 5/32" D, body length 1.00". Color: Black

206HEADLIGHT,12V HALOGEN (20)
1
High-impact housing and plastic stone guard. Clear lens, with 12volt-55w bulb. Approximate dimensions: 6" (152.4mm) W x 30/2" (88.9mm) H x 4" (101.6mm) D. For replacement bulb order P/N 206RB; for replacement lens order P/N 206L
Used On: Universal applications on many golf cars.

BULBJ2V HALOGEN (10)
12-volt halogen automotive bulb. Replacement bulb for P/N 206 headlight.
Used On: Universal application on many golf cars and industrial vehicles.

210RIVET, DRIVE, BLACK
Plastic rivet with center drive pin. Approximate measurements: Head 5/8" D, body 1/4" Dr stem 5/32" D, body length 3/4". Color: Black

210WRIVET, DRIVE, WHITE
Plastic rivet with center drive pin. Color: White.

212A
UGHT,12V, AMBER
tmp83CA-268.jpg
Mounts with rivets or screws ( NOT included) on 2" centers. Has two wires, 12-volt single filament #1895 bulb and measures approximately 2-1/4" H x 4-11/16" L x 9/16" thick. D.O.T. - APPROVED LENS!
Used On: Adaptable for use on many golf cars, trailers, utility vehicles, etc.

212RLIGHT.12V, RED
tmp83CA-269.jpg
Mounts with rivets or screws { NOT included) on 2" centers. Has two wires, 12-volt single filament #1895 bulb and measures approximately 2-1/4* H x 4-11/16" L x 9/16" thick. D.O.T. - APPROVED LENS!
Used On: Adaptable for use on many golf cars, trailers, utility vehicles, etc.

22288-G2
TAIL LIGHT,CC,EZ TXT.YAM
tmp83CA-270.jpg
Red, rectangular tail light assembly with metal mount plate. Uses P/N 15358 replacement bulb.
Used On: Club Car gas and electric, 81-UP; E-Z-Go gas and electric, 94-UP (Medalist/TXT); Yamaha 4-cycle gas and electric, 95-UP (G14, G16, G19, G20, G21, G22); Universal applications on many golf cars.

23359-G1 SPRING, BRAKE SHOE, CC, EZ, YAM
14-coil spring. Measures approximately 3-3/16" long. (1-7/16" hook on one end, 3/4* on other)
Used On: Club Car gas and electric, 80-UP; E-Z-Go gas and electric, 86 1/2 to 96; Hyundai gas and electric, 90-UP; Jacobsen; Yamaha gas and electric, 79-89 (G1) and 85-92 (G2, G8, G9).

248
BEARING, 6206 (10)
tmp83CA-271.jpg
Ball bearing, open both sides. Measures approximately 2.45" (62.2mm) O.D. x 1.16" (29.8mm) I.O. x .63" (16mm) W.
Used On: Club Car gas, 84-91; E-Z-Go 2-cycle gas, 76-UP; Yamaha 2-cycle gas, 78-89 ignition side (GU
1012874

255
BEARING, 6306
tmp83CA-272.jpg
Ball bearing, open both sides. Measures approximately 1.18* (29.9mm) I.D. x 2.83" 171.9mm) O.D. x .75" (19mm) W.
Used On: Club Car gas, 84-91; Yamaha 2-cycle gas, 78-89 clutch side (G1), Yamaha 4-cycle gas. 85-95 clutch side (G2, G8, G9, G11.G14).
1012867
1016565

25523-G4SPARK PLUG, BPR5ES (4,120)
NGK BPR5ES.
Used On: Club Car Gas, 00-UP; E-Z-Go 4-cycle gas, 96-UP (Workhorse ST350); Hyundai.
1018811-01

BEARING, 60052RS (12)
tmp83CA-273.jpg
Ball bearing, sealed both sides. For use on Yamaha inner front wheel. Also used on Club Car rear axle (NOT available separately from Club Car). Measures approximately .98" (25mm) I.D. x 1.85" (47mm) O.D. x .47* (11.9mm) W.
Used On: Club Car electric, 76-84; Cushman (with Terrell axles); E-Z-Go (with Terrell axles); Yamaha gas and electric, 82-UP (G1. G2, G8. G9, G14, G16, G19, G20, G21).

26739-G01
BEARING, 6207
tmp83CA-274.jpg
Ball bearing, open both sides. Measures approximately 1.36" (34.9mm) I.D. x 2.83" (71.9mm} O.D. x .67" (17mm) W.
Used On: Club Car gas FE350, 96-UP; E-Z-Go 4-cycle gas, 91-UP; Yamaha gas, 96-UP clutch side (Gil, G16, G20, G21, G22).
1017487

268
BEARING, 62052RS (10)
tmp83CA-275.jpg
Ball bearing, sealed both sides. Measures approximately .98" (24.9mm) I.D. x 2.05" (51.9mm) O.D. x .59- (14.9mm) W.
Used On: Club Car gas, 84-UP and electric, 84-86 (inner rear axle); Columbia'Harley gas and electric, 96-00 (rear axle) and 2-cycle gas, 82-95; Cushman (differential); E-Z-Go; Noland; Nordskog; Pargo; Taylor Dunn; Yamaha 4-cycle gas, 85-95 (input shaft) and electric, 81-92 (input shaft).
 
1011291
1011317
1012677
1012685
1012726
1013777
1013793
7336

27944-G1SPRING KIT. BRAKE, CC, EZ, YAM
r >                      Includes upper and lower tension springs,
Ii * 2 11 adjuster spring, two cup and spring * ' assemblies and two retainer pins.
Used On: Club Car gas and electric, OO-UP; E-Z-Go gas and electric, 97-UP; Yamaha gas and electric. 93-UP <G14, G16, G19).
1018163-01

282STARTER GENERATOR, CC, CHD
tmp83CA-276.jpg
Hitachi-style starter-generator.
Used On: Club Car gas, 84-96; Columbia/Harley 2-cycle gas, 67-95.
1012316101829401

292
BEARING, 6203 2RS
tmp83CA-277.jpg
Ball bearing, sealed both sides. For outer front wheel. Measures approximately .66" (16.8mm) I.D. x 1.57' <39.9mm) O.D. x AT (11.9mm) W.
Used On: Club Car; Columbia/Harley; Cushman; E-Z-Go; Jacobsen; Toro; Yamaha gas and electric, 78-81.
1011290
1012877

293BRAKE DRUM, CC, CHD, EZ, YAM (8)
tmp83CA-278.jpg
Machined casting with a 4 on 4 bolt pattern. Measures approximately 6.28" I.D. Brake shoe surface area is 1.34" wide.
Used On: Club Car gas and electric, 81-94; Columbia/Harley; E-Z-Go; Yamaha gas and electric, 82-UP.
1011137

30110-77GENERATOR END CAP, W/BRUSHES
tmp83CA-279.jpg
Replacement for Hitachi-style starter-generator.
Used On: Club Car gas, 84-96; Columbia /Harley 77-UP {Hitachi style); E-Z-Go gas, 80-UP; Hyundai gas, 91-UP IHGG1); Yamaha gas, 78-95 (G1, G2, G8, G9, G14).
1012993101876402

30111-77GENERATOR END CAP, BELT SIDE
tmp83CA-280.jpg
Replacement for Hitachi-style starter-generator.
Used On: Club Car gas, 84-UP; Columbia /Harley 77-UP (Hitachi style); E-Z-Go 2-cycle gas, 80-UP; Yamaha 2-cycle gas, 78-89 (G1).
1012999

30149-67
BEARING, 62022RS (10)
tmp83CA-281.jpg
Ball bearing, sealed both sides. Measures approximately .59" (14.9mm) I.D. x 1.38" (35mm) O.D. x .43" (10.9mm) W.
Used On: Club Car gas; Columbia/Harley gas. 67-95; Cushman; E-Z-Go 2-cycle gas. 78-94 and 4-cycle, 91-UP; Hyundai gas; Melex; Toro; Yamaha gas, 78-UP (G1, G2, G8, G9.G16).
1012884 1013005 1013050

30151-69
BEARING, 63032RS (10)
Ball bearing, sealed both sides. Measures approximately .67" <17mm) I.D. x 1.85" (46.9mm) O.D. x .55" (13.9mm) W.
Used On: Club Car gas; Columbia/Hariey 2-cycle gas, 67-95; E-Z-Go; Hyundai gas; Melex; Yamaha gas. 78-UP (G1. G2, G8, G9).
tmp83CA-282.jpg
1012687
1013001

30443-77BRUSH SET. GEN, CC, CHD, EZ, YAM
Set of 4 brushes for use in Hitachi-style
Lt f f starter-generator. Measures approximately jU «U L-. 1" L x 17,'32- W x 7/32" thick.
Used On: Club Car gas, 84-96; Columbia/Harley gas, 67-UP; E-Z-Go gas, 80-UP; Hyundai gas, 91-UP; Yamaha gas, 78-UP (G1, G2, G8, G9, 611, G14, G16).
1013023 1014699 1018693-01

30860-77 ARMATURE, STARTER, CC, CHD, EZ, YAM
Armature only for Hitachi-style starter-generator.
Used On: Club Car gas, 84-96; Columbia/Harley 2-cycle gas, 69-98 early; E-Z-Go 2-cycle gas, 80-94; Hyundai gas. 91-UP; Yamaha gas, 78-95 (G1, G2, G8, G9, G11.G14).
1013004

313FRFOOTREST, ALUMINUM
Made of heavy gauge diamond plate aluminum for use with rear-facing seat installations. (Measures approximately 34-1/4" W, 6-3/4" D, with a 2-1/2" mounting lip}. Excellent for use with 312Wor3i2B.
Used On: Universal use for many types of golf cars and industrial vehicles.

335ABRAKE SHOES, CC, EZ, YAM
pit
Bonded lining measures approximately 1-3/16" wide. Rear lining is approximately 5-15/16" long; front is approximately 6' long.
Used On: Club Car 95-UP; Columbia/Harley gas and electric, 86-UP; E-Z-Go gas and electric, 87-96; Hyundai gas and electric (HGB1, HGB1 A, HGG1); Jacobsen; Yamaha gas and electric, 82-93 (G1, G2, G8, G9).
1018232-01

335B BRAKE SHOE, SHORT/FRONT
tmp83CA-283.jpg
Bonded lining measures approximately 1-3/16" Wx 6" L
Used On: Club Car gas and electric, 95-UP; Columbia/Harley gas and electric, 86-UP; E-Z-Go gas and electric, 87-96; Hyundai gas and electric, 91-UP; Yamaha gas and electric, 82-93 (G1, G2, G8, G9).

335CBRAKE SHOE, LONG/REAR
tmp83CA-284.jpg
Bonded lining measures approximately 1-3/16" Wx 5-15/16" L
Used On: Club Car gas and electric, 95-UP; Columbia/Harley gas and electric, 86-UP; E-Z-Go gas and electric, 87-96; Hyundai gas and electric, 91-UP; Yamaha gas and electric, 82-93 (G1, G2, G8, G9).

T
339RIVET, PUSH, BLACK
Black colored 'push-in" type rivet made of ABS plastic for 1/4" hole size. Approximate measurements: Head diam­eter 0.685"; stem diameter 0.275"; stem length 0.820"; effective grip length 0.525".

T
3391RIVET. PUSH, IVORY
Ivory colored "push-in" type rivet made of ABS plastic for 1/4" hole size. Color matched to Yamaha ivory. Approximate measurements: Head diameter 0.685"; stem diameter 0.275"; stem length 0.620"; effective grip length 0.400".

345
SPARK PLUG, BPM4A, CC (10,200)
NGK BPM4A.
Used On: Club Car gas, 84-91.
1012522
tmp83CA-285.jpg

400SB SWEATER BASKET. CC 81-90 (14)
tmp83CA-286.jpg
TPfo- Strong wire mesh construction, vinyl -I J j! j I'jfji dipped for superb durability. Basket '---Ji& measures approximately 9" (228.6mm) x ;$$ 17-1/4" (438.15mm) at top and 7-1/2" T* (190.5mm) x 15-1/2" (658.3mm) at bottom, 11" (279.4mm) deep. Color: Black.
Used On: Club Car gas and electric, 81-90.

4240MICRO SWITCH, TERM, CC (100)
tmp83CA-287.jpg
Lever-type switch with three spade terminals (N.O., N.C.. COM.).
Used On: Club Car electric, accelerator switch, 70-UP, gas component box 84-UP and gas F/R shifter 84-UP; Cushman; Noland.
10148071014887

43152-66 NUT. LUG. 1/2"-20. CC, CHD. E2
tmp83CA-288.jpg
1/2-20 thread zinc plated steel iug nut.
Used On: Club Car; Columbia/Harley; Cushman; E-Z-Go; Jacobsen; Melex; Nordskog; Pargo; Taylor Dunn.
10109841011390

497                            CLEVIS PIN, 5/16" X I"
tmp83CA-289.jpg
Plated pin with drilled hole for cotter pin. Uses P/N 10387-G1 cotter pin (NOT included).
Used On: Club Car gas and electric. 81-UP; Columbia/Harley; Davis; E-Z-Go gas and electric, 65-UP; Jacobsen; Karrior; Legend; Melex; Nordskog; Pargo; Taylor Dunn.
1010829

61254-89GAS CAP, CHD
tmp83CA-290.jpg
Gas cap and seal, without gauge.
Used On: Club Car; Columbia/Harley gas, 75-95; Hyundai gas, 91-UP.
1012306

62350-63
FILTER, FUEL, 1/4", CC, CHD, EZ
tmp83CA-291.jpg
In-line 1/4" clear plastic filter. (Will NOT snap into Club Car frame).
Used On: Club Car gas, 84-UP; Columbia/Harley; E-Z-Go 2-cycle gas, 76-94 (Marathon); Jacobsen; Many applications for golf and utility vehicles using 1/4" fuel line.
1012342

63501-68
FUEL LINE, 4 FOOT
tmp83CA-292.jpg
1/4" I.D. hose.
Used On: Club Car; Columbia/Harley gas, 63-UP; E-Z-Go; Jacobsen; Noland.
1012293 1012458 1013681
1012297 1013290 1013682
1012298 1013679

66036-72DC RECEPTACLE, 2 PRONG
Use with P/N 607 2-prong DC charger plug. Includes hardware.
f                                    Used On: Club Car 36-volt electric, 74-UP;
! \ \° Columbia/Harley electric; Cushman; E-Z-o o ' Go; Hyundai electric, 90-UP; Karrior; Legend; Melex; Noland; Nordskog; Pargo; Taylor Dunn; Yamaha.
17756-G14107 CC
82578428
J22-86181-00                    JN4-H6181-00
tmp83CA-293.jpg

66063-69BDC CORD, CROWFOOT GRAY PLUG
tmp83CA-294.jpg
8-1/2' DC cord with molded gray housing and 2-prong CROWFOOT plug.
Used On: Club Car; Columbia; Cushman; E-Z-Go; Karrior; Legend; Melex; Noland; Nordskog; Taylor Dunn; Yamaha.
101307610137531016433-01
14835-G116152-G116442-G1
18636-G1413366063-69A 9000907

66069-72
DC RECEPTACLE. 2 OR 3 PRONG
For P/N 607 2-prong CROWFOOT DC plug, or P/N 15210 3-prong plug with "L'-shaped guide. Mount plate measures approximately 2-1/4" x 3-11/16". Includes four mount screws.
Used On: Columbia/Harley electric; Cushman electric; E-Z-Go electric.
tmp83CA-295.jpg
f T 1 \

66515-76FUSE ASSEMBLY. 30A
tmp83CA-296.jpg
30-amp fuse for chargers with clear plastic
! ^i^^ % fuse cover.
f , T ° Used On: Club Car 48-volt electric, 95-UP (PowerDrive); Lester models 6430, 6720, 7710, 7850, 8714, 9032, 9611. 9695. 9700, 13165,14100,14390,17910 and others.
101210131567-G1
7422L8776

66520-72DC RECEPTACLE, BUILT IN CHARGER
tmp83CA-297.jpg
Three-pronged, grounded male receptacle on a phenolic base, which is riveted to a stamped steel "stand-off" housing. Measures approximately 1-5/8" high and mount holes are 2-1/16' to centers.
Used On: Columbia/Harley electric; Nordskog.

F & R SWITCH ROTOR, CC 76-83 1/2
injection molded for F & R switch assembly.
Used On: Club Car electric, 76-83 1/2.

7048
BUSHING, SPINDLE LOWER, CC 79-UP
tmp83CA-298.jpg
Flange-type bushing. Measures approximately .75" (19mm) I.D. x .94" (23.8mm) O.D. x 1" (25.4mm) L. Flange measures approximately 1.24" (31.7mm) O.D. x.13" (3.3mm) W.
Used On: Club Car gas and electric, 79-UP.

70491 -73BRUSH SET, MOTOR, CC, CHD, EZ
f f f
L L W
Set of 4 brushes for GE motors. Measures approximately 1-3/8" L x 5/8" W x 1/2"
thick.
Used On: Club Car electric, 76-80; Columbia/Harley electric, 73-85; Cushman electric; E-Z-Go electric, 73-79; Noland; Otis, with GE motors.
7363

7080FLOORMAT. CC 81-UP
tmp83CA-299.jpg
Die cut 3/16" thick rubber with pebble-texture finish.
Used On: Club Car gas and electric, 81-UP.
1010766 1011028 1014754 1015032 7088

24-36V, 275A, WO/D
Solid state electronic speed controllers.
(W/D) Equipped with "disable" feature which helps prevent the rear wheels from spinning during rapid acceleration.
(WO/D) Not equipped with "disable" feature.
NEW

71856-G01BUCKLE CLAMP BAG STRAP CC, EZ
tmp83CA-300.jpg
Injection molded bag strap clamp.
Used On: Club Car gas and electric 81-UP (DS); E-Z-Go 4-cycle gas and electric 94-UP IMedalist/TXT).
1013754

720MOTOR. 36V, 3.5HP, 10SP, CC, E2
tmp83CA-301.jpg
Advanced DC motor with 10-spline armature.
Used On: Club Car 36-volt electric, 84-UP; E-Z-Go electric, 76-86 1/2.
1014678 1017728-02 1018134-01

72084-G01FILTER, FUEL, CC, EZ, YAM
tmp83CA-302.jpg
In-line 1/4" - 5/16* clear plastic filter with stepped flange.
Used On: Club Car; E-Z-Go 4-cyc!e gas. 94-UP (Medalist/TXT); Yamaha 2-cycle gas, 78-89 (G1) and 4-cycle gas, 94-UP IG14, G16. G20, G21, G22).
1020032-01K1020O32-01

72367-72BRUSH SET, MOTOR, CC, CHD, E2
tmp83CA-303.jpg
Set of 4 brushes with spring hooks for GE motors. Measures approximately 1-5/8' Lx 5/8" W x 1/2* thick.
Used On: Club Car electric; Columbia/Harley electric; Cushman electric; E-Z-Go electric, 65-72; Melex; Taylor Dunn, with GE or Westinghouse Motors.
80898785

7241RESISTOR BOARD, CC 74-75
tmp83CA-304.jpg
Insulator board with six 1/4" pre-drilled holes. Measures approximately 2-1/4" x 7-11/16%
Used On: Club Car electric, 74-75.

7273OIL SEAL, FRONT WHEEL. CC 76-81
Seal measures approximately 1.10" 127.9mm) I.D. x 1.78" (45.3mm) O.D. x .46" U 1.8mm) W.
Used On: Club Car electric, 76-81; Cushman; Legend.

7274
BEARING CONE ONLY, LM11949
tmp83CA-305.jpg
Tapered roller bearing for 3/4" front axles or spindles.
Used On: Club Car, 74-UP; Columbia/ Harley 3W, 63-84; Cushman; E-Z-Go 3W, 67-UP; Jacobsen; Legend; Taylor Dunn.

7275
DUST COVER, CC 74-81
tmp83CA-306.jpg
Steel cover snaps into wheel hub to keep dirt and grime away from wheel bearings.
Used On: Club Car electric, 74-81.

7308BEARING CUP ONLY, LM11910
tmp83CA-307.jpg
Bearing cup (race) only, for 3/4" front axles or spindles. Use with P/N 7274 bearing.
Used On: Club Car. 74-UP; Columbia/ Harley 3Wr 63-84; Cushman; E-Z-Go 3W, 67-UP; Jacobsen; Legend; Nordskog; Otis; Taylor Dunn; Toro.

73120-G05BRUSH SET. ADVANCED DC MOTOR, EZ
tmp83CA-308.jpg
Set of 4 brushes with hardware and insulators. Measures approximately 1-3/16rLx 15/16" Wx 11/32'thick.
Used On: Club Car electric. 94-UP; E-Z-Go electric. Advanced DC electric motor only.

7333BEARING, REAR AXLE, 6006NR
tmp83CA-309.jpg
Ball bearing, open both sides, with snap-ring retainer. Measures approximately 1.17" (29.8mm) I.D. x 2.16* (54.9mm) O.D. x .51" (12.9mm) W.
Used On: Club Car electric, 84-86; Cushman; Noland; Pargo.

7352BRAKE SHOES, CC, CHD
tmp83CA-310.jpg
Bonded lining measures approximately 1-5/16" W x 7" L. (4 per set)
Used On: Club Car 73 and earlier; Columbia/Harley; Nordskog; Otis; Taylor Dunn.

74509-76
VOLTAGE REGULATOR, CC, CHD, EZ, YA
tmp83CA-311.jpg
For use with Hitachi-style starter-generator.
Used On: Club Car gas, 84-91; Columbia/ Harley 2-cycle gas. late 76-84; E-Z-Go 2-cycle gas, 80-UP; Hyundai gas, 91-UP; Yamaha gas, 78-91 (G1, G2, G9).
1012422

751POT BOX, PB-6 STYLE
tmp83CA-312.jpg
Curtis PB-6 style, with lever and return spring.
Used On: For most applications using Curtis controller.

7539TIE ROD END, RIGHT THREAD, CC (2, 50)
tmp83CA-313.jpg
Includes grease fitting, seal, castellated-nut and cotter key. Right hand threads.
Used On: Club Car gas and electric. 74-UR 1011893

7540
TIE ROD END, LEFT THREAD, CC (25)
tmp83CA-314.jpg
Includes grease fitting, seal, castellated-nut and cotter key. Left hand threads.
Used On: Club Car gas and electric, 74-UP. 1011895

7715SPRING SET. BRAKE SHOE, CC 74-75
Upper and lower pivot tension springs.
Used On: Club Car electric 74-75; ColumbiayHarley; Nordskog; Otis; Taylor Dunn.

7719BUSHING, ARM, CC 82-92
tmp83CA-315.jpg
Flange-type bushing. Measures approximately .50" (12.7mm) I.O. x .62" (15.9mm) O.D. x .750" (19mm) L Flange measures approximately .88" (22.4mm) O.D.x.13M3.3mm)W.
Used On: Club Car gas and electric, 82-92.

7841
BUSHING, STEERING TUBE, CC, CHD, EZ
tmp83CA-316.jpg
Injection molded black plastic flange-type bushing. Measures approximately .76' 119.3mm) I.D. x 1.42" (36.1mm) O.D. x .4902.4mm) L. Flange measures approximately 1.47" <37.5mm) O.D. x .12" (3.1mm) W.
Used On: Club Car gas and electric, 76-84; Columbia/Harley; Cushman; Davis; E-Z-Go gas and electric, 65-70; Jacobsen; Melex; Noland; Nordskog; Otis; Pargo; Toro.

7906
OIL SEAL, REAR AXLE, CC 76-84, EZ
Seal measures approximately 1.12* (28.6mm) I.D. x 1.84" (46.8mm) O.D. x .30" (7.7mm) W.
Used On: Club Car electric. 76-84; Cushmani with Terrell axles); E-Z-Go (with Terrell axles); Legend; Noland.
tmp83CA-317.jpg

8067BUSHING, SPINDLE UPPER, CC 79-UP
tmp83CA-318.jpg
Upper spindle bushing. Approximate measurements: .94" <23.9mm) O.D. x .75' (19mm) I.D. x 1" {25.4mm) L
Used On: Club Car gas and electric, 79-UP.

8204
KEY SWITCH, CC E7S-83 1/2
Switch includes P/N 1014173 keys (2). Used On: Club Car electric, 76-83 1/2.

8224
WHEEL CYLINDER, PASS. CC 74-80
tmp83CA-319.jpg
Wheel cylinder assembly, passenger side. Used On: Club Car electric, 74-80; Pargo.

8225
WHEEL CYLINDER, DRIVER, CC 74-80
tmp83CA-320.jpg
Wheel cylinder assembly, driver side. Used On: Club Car electric, 74-80; Pargo.

82842-86BRUSH SET, MOTOR. CC, CHD, EZ
a> A f= I* Set of 4 brushes. Measures approximately C r Y V 1-3/8" L x 5/8" W x 1/2" thick.
Used On: Club Car electric; Columbia/ Harley electric; Davis; E-Z-Go electric; Nordskog; Pargo; Taylor Dunn.

82918-79 BRUSH SET, MOTOR, CC. CHD, YAM
LLLt
Set of 4 brushes for Hitachi electric motors. 1-1/8" L x 23/32" W x 5/8" thick.
Used On: Club Car electric, 80-84; Columbia/ Harley electric; Yamaha electric, 80-88 (G1, G2). Hitachi electric motors only.
10113321011424

8541RESISTOR COIL BRACKET, CC 76-87
tmp83CA-321.jpg
Stamped steel, zinc plated "offset" bracket. Measures approximately 1" W x 1-1/2 overall length.
Used On: Club Car electric, 76-87.

8638BRAKE SHOES, CC E76-80
tmp83CA-322.jpg
Bonded lining measures 1-1/2" W x 6-5/8* L Used On: Club Car electric, 76*80; Pargo. 10165568227

8991 MICRO SWITCH, TERM, CC (100)
tmp83CA-323.jpg
Lever-type switch with 2 spade terminals (N.O., COM).
Used On: Club Car electric, accelerator speed switch, 81-84, gas component box 84-UP and gas F/ R shifter 84-98.
1014808

8996
MASTER CYUNDER, CC 74-80
For Mercury style brakes.
Used On: Club Car electric, 74-80.
72808719
tmp83CA-324.jpg

BEARING SET, LM11910/LM11949
tmp83CA-325.jpg
Tapered roller bearing and race assembly. Measures approximately .74" (18.7mm) I.D. x 1.8U (45.2mm) O.D. x .47" (12mm) W. (Overall width including shoulder on inner race is .66")
Used On: Club Car, 74-UP; Columbia/ Harley 3W, 63-84; Cushman; E-Z-Go 3W, 67-UP; Jacobsen; Legend; Nordskog; Otis; Taylor Dunn; Toro.
1011393

909
LIGHT KIT, RECESSED, CC 93-UP
Includes a pair of rectangular halogen headlights, amber front running lights, red rear tail lights, wiring, connectors, switch and complete installation instructions.
Molded of black, high-impact ABS plastic. Used On: Club Car gas and electric, 93-UP.
tmp83CA-326.jpg
minim
41 4 k.......kfcfck

tmp83CA-327.jpg
909A
BEZEL & HEADLIGHT, CC 93-UP
Includes a pair of rectangular halogen headlights with left and right bezels. Does NOT include wiring harness, tail lights, amber-front runners, or connectors.

tmp83CA-328.jpg
BEZEL. DRIVER, CC 93-UP

909R
BEZEL, PASS, CC 93-UP
tmp83CA-329.jpg

tmp83CA-330.jpg
SHOCK BUSHING KIT, CC, EZ
For most 3/8-24 threaded stud mount shock absorbers. Kit includes rubber bushings (2), retainer washer (2) and 3/8-24 hex pal nut (1). Kit is good for one shaft. Used on P/N's 1014236, 13270-G1, 15707-G1. 20278-G1, 20279-G1 and 70324-G01 shocks.
Used On: Club Car; Cushman; E-Z-Go. 1010142 1010144 1011415