|
1012466GASKET,
STEERING TUBE, CC, CHD. EZ
|
|||
 |
Die-cut
foam gasket. Measures approximately
3/4" I.D. x 1-3/8" O.D. x 7/16" W.
Used
On: Club Car gas and electric, 76-94; Columbio/Harley; Cushman; Davis;
E-Z-Go gas and electric, 65-70; Jacobsen; Legend; Noland; Otis;Toro.
|
||
|
1016467
|
FILTER,OIL,
CC, 92-UP (50)
Spin-on
type filter with gasket.
Used
On: Club Car gas, 92-UP (OHV engine only); Cushman.
|
||
 |
|||
|
1017489
|
FLASHER,
12 VOLT, CC 93-UP
|
||
 |
Three-prong
flasher unit.
Used
On: Universal application where 12-voit turn signal switch is used.
|
||
|
10606G2
|
MICRO
SWITCH, ROLLER, EZ <20)
|
||
 |
Roller
arm style lever with three terminals {N.O., N.C., COM.}. For use with F
& R switch.
Used
On: Cushman; E-Z-Go gas and electric, 65-UP {non DCS) and 83-94 accelerator
(Marathon); Jacobsen; Legend; Melex; Noland;Taylor Dunn.
|
||
|
11877-G1
|
RESISTOR
COIL ASSY, EZ 70-84
|
||
 |
„
Insulator board with 3 resistor coils { 1st, [/
2nd and 3rd speed}.
Used
On: Cushman electric; E-Z-Go electric, 70-84.
|
||
|
11989-G1F
& R HANDLE, EZ 65-85
|
|||
 |
Shaft
is 2-1/4" long with 5/16"-18 threads on
each end. Includes a molded black plastic knob and jam nut.
Used
On: Cushman; E-Z-Go gas and electric,
65-85 (Marathon); Legend; Melex (S/N's to 155058); Noland.
|
||
|
12064-G1NUT,
PUSH, 5/16'
|
|||
|
o
|
5/16"
push nut for hill brake pedal pin. Used On: Cushman; E-Z-Go; Noland. 604146
|
||
|
12305-G1
. RETAINING
RING, CC, CHD, EZ
|
|||
 |
Push
type clip for retaining brake cables. Zinc plated to resist corrosion.
Used
On: Club Car gas and electric, 81-UP; Columbia/Harley gas and electric,
86-UP; Cushman; E-Z-Go gas and electric, 68-UP; Legend;Jacobsen.
|
||
|
13465-G1
|
SPRING,BRAKE
SHOE, EZ
|
||
 |
Pedal
return spring, green.
Used
On: Cushman; Davis; E-Z-Go gas and electric, 77-81; Jacobsen;Toro.
|
||
|
13465-G2
|
SPRING,BRAKE
SHOE, EZ
|
||
|
Pedal
return spring, red.
Used
On: Cushman; Davis; E-Z-Go gas and electric, 77-81; Jacobsen;Toro.
|
|||
|
13955-G1
|
BRAKE
SHOES,SET OF 4
|
||
 |
Riveted
lining measures approximately 1-3/4" wide and 6-7/8" long. (Set of 4)
Used
On: Cushman; Davis; E-Z-Go gas and electric, 76-81; Jacobsen;Toro. May
also be used for E-Z-Go pre 1975 but is not an exact replacement.
|
||
|
14608-G1
|
REVERSE
BUZZER,CC,CHD,EZ
|
||
|
24,'36-volt
heavy-duty warning buzzer. (Not the same configuration as OEM buzzer).
Used
On: Club Car electric, early 70-UP; Columbia/Harley;
Cushman; E-Z-Go electric. 65-83, Legend; Mclcx; Noland.
|
|||
|
14651-G1
|
F
& R BOARD W/CONTACTS, EZ
Board
with 4 contacts and 2 stops.
Used
On: Cushman; E-2-Go electric 71-UP {NON
DCS), gas 76-94 (Marathon); Jacobsen; Legend; Noland.
|
||
 |
|||
|
15355HEADUGHT.SEALED,
9000 CP
|
|||
 |
Automotive
replacement for #4415. 9000 candle power with 2 screw on-terminals.
Used
On: Cushman; Otis.
|
||
|
15426
|
POTENTIOMETER,
CURTIS 98191
|
|||
 |
Used
with Curtis pot box.
|
|||
|
Used
On: Club Car; Cushman; E-Z-Go (Marathon);
Melex.
|
Columbia/Harley;
olectric, 89-94
|
|||
|
15436-G1BUSHING,
INSULATED, .335 x .345
Square
plastic insulator bushing. Measures
approximately .335* I.D. x .550" O.D.
x .345" thick.
Used
On: Columbia/Harley electric; Cushman; Davis; E-Z-Go electric, 70-92;
Legend; Nolancl; Nordskog; Pargo (GE motors}.
|
||
|
15573
|
SCREW
STUD, #8-32 x .885
#8-32
x .885" cadmium plated steel screw {stud) for moving contact, P/N 417.
|
||
 |
|||
|
15576
|
STUD,BRASS,3/8
HEX, 1/4-20
|
|||
 |
Brass
stud for mounting contact to movable
arm. 1/4*-20 threads on each end, with 3/8" hex.
Used
On: Cushman electric.
|
|||
|
15578CIRCUIT
BREAKER, 12V-20A
|
|||
 |
Self-resetting
circuit breaker with stud type, terminals. 12-volt 20-amps.
Used
On: Cushman; Noland.
|
||
 |
||
|
15579
NUT. LUG. 7/16"-20
|
||
|
7/16-20
thread zinc plated steel lug nut. Used
On: Cushman.
|
||
|
15913CONTROLLER,
REBUILT, 1205-101
|
|||
 |
24/36-volt,
400-amp REBUILT Curtis solid-state electronic speed controller. Equipped
with "disable" feature which helps prevent the rear wheels from spinning
during rapid acceleration.
Used
On: Columbia/Harley 96-UP; Cushman;
E-Z-Go; Melex; Nordskog.
1205-101832858
|
||
|
16917-G1BRUSH
SET, MOTOR,CC,CHD,EZ,HYU
|
|||
 |
Set
of 4 brushes (with studs} for GE motors.
Measures approximately 1-7/16* I x5/8"W,
1/2" thick.
Used
On: Club Car electric, 80-93; Columbia/Harley electric, 86-90; Cushman
electric; E-Z-Go electric, 80-92; Hyundai electric; Legend; Nordskog;Taylor
Dunn.
|
||
|
21719-G1STARTER
DRIVE KIT, EZ
|
|||
 |
For
U.T. starter. Includes spring, flat washer, collar and rubber boot.
Used
On: Cushman; E-Z-Go Utility Truck.
|
||
|
409
|
CONTACT
MOVABLE, CUSHMAN
|
||
 |
Insulated
contact for forward and reverse switch assembly.
Used
On: Cushman electric; Otis.
|
||
|
415
|
CONTACT,
STATIONARY, CUSHMAN
|
||
 |
Solid
copper alloy 1-3/8" L x 1/2" W x 1/4" thick, with two 1/4"-20 threaded
holes.
Used
On: Cushman speed switch.
|
||
|
417CONTACT,
MOVABLE, CUSHMAN
|
|||
 |
Solid
copper alloy, 1-5/8" L x 3/4" W x 1/4" thick, with 8-32 threaded mount
stud and one 1/4"-20 threaded
hole. Uses replacement stud P/N 15573.
Used
On: Cushman speed switch assembly.
|
||
|
4240MICRO
SWITCH, 3 TERM, CC (100)
|
|||
 |
Lever-type
switch with three spade terminals {N.O., N.C., COM.). Used on the forward/reverse
switch to control the reverse warning buzzer.
Used
On: Club Car 70-UP; Cushman; Noland.
|
||
|
70491-73BRUSH
SET, MOTOR, CCfCHD,EZ
|
||
|
Set
of 4 brushes for GE motors. Measures
£f
r F approximately 1-3/8" L x 5/8* Wx 1/2'thick. far mr «?*
used Qn: Club Car electric, 76-80; Columbia/Harley electric, 73-85; Cushman
electric; E-Z-Go electric, 73-79; Nolans-Otis,
with GE motors. ' ' — -
|
||
|
717CONTROLLER,
24-36V, 275A, W/D
|
|||
 |
24/36-volt,
275-amp solid-state electronic speed controller. Equipped with "disable"
feature which helps prevent the rear wheels
from spinning during rapid acceleration.
Used
On: Columbia/Harley; Cushman; E-Z-Go; Melex; Nordskog.
|
||
|
72002-51SWITCH,
BRAKE LIGHT, CHD
|
|||
 |
Screw-in
type, hydraulically actuated 2-prong switch.
Used
On: Columbia/Harley; Cushman; Nordskog.
|
||
|
72342-73WASHER,
FIBER, .330, SQUARE
|
|||
 |
Square
fiber insulator washer. Measures approximately .330" I.D. x .895" O.D.
Used
On: Columbia/Harley electric; Cushman electric (GE motors); E-Z-Go electric
(GE motors); Noland; Nordskog.
|
||
|
72367-72
|
BRUSH
SET, MOTOR, CC,CHD,EZ
|
||
 |
Set
of 4 brushes with spring hooks for GE motors.
Measures approximately 1-5/8* L x 5/8MWx 1/2" thick.
Used
On: Club Car electric; Columbia/Harley
electric; Cushman electric;
E-Z-Go electric, 65-72; Melex; Taylor
Dunn, with GE or Westing house Motors.
|
||
|
7273OIL
SEAUFRONTWHEEUCC 76-81
|
|||
 |
Seal
measures approximately 1.100" (27.94mm) I.D. x 1.785" (45.33mm) O.D.
x .467" (11.86mm) W.
Used
on: Club Cor electric, 76-81; Cushman;
Legend.
|
||
|
7841
|
BUSHING,STRI\IG
TUBE,CC,CHD,EZ
|
||
 |
Injection
molded black plastic flange-type bushing. Measures approximately .762"
(19.35mm) I.D. x 1.422" <36.11mm) O.D. x .497" L. Flange measures approximately
1.479" (37.56mm) O.D. x .125" (3.17mm) W.
Used
On: Club Car gas and electric, 76-84; Columbia/Harley; Cushman; Davis;
E-Z-Go gas and electric, 65-70; Jacobsen; Melex; Noland; Nordskog; Otis;
Pargo;Toro.
|
||
|
82704-78OIL
SEAL, AXLE, CHD, EZ
|
|||
 |
Oil
seal for Oana style differentials.
Used
On: Columbia/Harley; Cushman; Davis; E-2-Go; Hyundai; Jacobsen; Melex;
Nordskog.
|
||
|
82837-86BUSHING,
INSULATED, .335 x .227
Square
plastic insulator bushing. Measures
approximately .335" I.D. x .550" O.D.
x .227" thick.
Used
On: Columbia/Harley electric; Cushman; Davis; E-Z-Go electric, 70-92; Noland;
Nordskog <GE motors).
|
||
|
82840-86COMMUTATOR
STUD, CHD, EZ
|
|||
 |
Crossover
stud (5/16"-18 x 1-1/2") with insulated lead wire and eyelets.
Used
On: Columbia/Harley electric; Cushman; E-2-Go electric; Pargo; Taylor Dunn.
|
||
|
83288-86 WASHER,
FIBER, .330, ROUND
|
|||
 |
Fiber
insulator washer. Measures approximately
.330" 1.0 x .845" O.D. x .135" thick.
Used
On: Columbia/Harley electric; Cushman;
Davis; E-2-Go electric, 70-92 (GE motors); Noland; Pargo.
|
||
|
83289-86
WASHER, FIBER, .475, ROUND
|
|||
 |
Insulator
washer. Measures approximately .475"
I.D X .875" O.D. x .122" thick.
Used
On: Columbia./Harley electric with GE motors;
Cushman; Davis; E-Z-Go electric, 70-92;
Noland; Nordskog; Pargo (GE motors).
|
||
|
944SHOCK
BUSHING KIT, CC, EZ
|
||
|
For
most 3/8"-24 threaded stud mount shock absorbers. Kit includes rubber bushings
(2), retainer washer (3), and 3/8"-24 hex nut {1}.
Used
On: Club Car; Cushman; E-Z-Go.
|
||